AuCom EMX4i Page 43 User Manual Download

Page: 43 / 126

KEYPAD AND FEEDBACK

EMX4i User Manual 710-14888-00C

Keypad and Feedback

7.1

The Keypad

Local keypad

Remote keypad (if installed)

Ready

Run

Trip

Local

Menu
Store

Exit

Reset

17691.

Start

Stop

Reset

LCL

RMT

Menu
Store

Exit

Alt

Logs

Tools

17692.

1  Four-line display for status and programming details.
2  Status LEDs
3  Menu navigation buttons:

: Exit the menu or parameter, or cancel a parameter change. On the local

keypad, this button also resets a trip.

: Enter a menu or parameter, or save a parameter change.

: Scroll to the next or previous menu or parameter, change the setting of

the current parameter or scroll through the status screens.

4  Shortcut to the command source menu in Setup Tools.
5  Soft starter local control buttons
6  Shortcut buttons for quick access to common tasks.

LOGS: Open the Logs Menu.
ALT: Select which graph to view, or pause/restart the graph (hold longer than
0.5 seconds)
TOOLS: Open the Setup Tools.

Summary of Contents for EMX4i































































































































Search results

Summary of Contents for EMX4i

Reviews:

Related manuals for EMX4i

Brands by name

Popular brands

AuCom EMX4i, User Manual

Search results

Summary of Contents for EMX4i

Reviews:

Related manuals for EMX4i

Brands by name

Popular brands