AuCom EMX4i Page 119 User Manual Download | Manualshive

Page: 119 / 126

background image

TROUBLESHOOTING

118

EMX4i User Manual 710-14888-00C

Display

Possible cause/Suggested solution

Overcurrent

The current has exceeded the level set in parameter 5E

Overcurrent

for longer than the time set in parameter 5F

Overcurrent Delay

. Causes can include a momentary overload

condition.
Related parameters: 5E, 5F, 6E

Overpower

The motor has experienced a sharp rise in power. Causes can
include a momentary overload condition which has exceeded the
adjustable delay time.
Related parameters: 5M, 5N, 6I

Overvoltage

There has been a voltage surge on the mains. Causes can
include problems with a transformer tap regulator or off-loading
of a large transformer load.
Related parameters: 5I, 5J, 6G

Parameter out of
range

This trip is not adjustable.

•

A parameter value is outside the valid range. The keypad will
indicate the first invalid parameter.

•

An error occurred loading data from the EEPROM to RAM
when the keypad powered up.

•

The parameter set or values in the keypad do not match the
parameters in the starter.

•

"Load User Set" has been selected but no saved file is
available.

Reset the fault. The starter will load the default settings. If the
problem persists, contact your local distributor.
Related parameters: None

Phase sequence

The phase sequence on the soft starter's input terminals (L1, L2,
L3) is not valid.
Check the phase sequence on L1, L2, L3 and ensure the setting in
parameter 5R is suitable for the installation.
Related parameters: 5R, 6P

«
...
117
118
119
120
121
...
»

Summary of Contents for EMX4i































































































































Reviews:

No comments

Related manuals for EMX4i

Brand: Rain Bird Pages: 24

ESP-LXIVM Series

Brand: Rain Bird Pages: 16

Brand: Rabe Pages: 61

Brand: Racal Instruments Pages: 35

Brand: Samson Pages: 6

U1000 iQpump Drive

Brand: YASKAWA Pages: 426

Brand: YASKAWA Pages: 26

Brand: YASKAWA Pages: 210

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 400

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 466

Brand: Gardena Pages: 236

Brand: Daikin Pages: 40

Brand: Carel Pages: 36

Brand: Handiquilter Pages: 53

Smart 4 Universal

Brand: Classic Pages: 12

Brand: Pilz Pages: 9

Brand: Tate Pages: 32

Brand: UPPAbaby Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands