manualshive.com logo in svg

AuCom EMX4i, User Manual, Page: 117 / 126

Share
Download
AuCom EMX4i User Manual Download Page 117

TROUBLESHOOTING 

116

   

 

EMX4i User Manual  710-14888-00C 

Display 

Possible cause/Suggested solution 

Low Control Volts 

The EMX4i has detected a drop in the internal control voltage. 

•

 

Check the external control supply (A1, A2, A3) and reset the 
starter. 

If the external control supply is stable: 

•

 

the 24 V supply on the main control PCB may be faulty; or 

•

 

the bypass driver PCB may be faulty. Contact your local 
supplier for advice. 

This protection is not active in Ready state. 
Related parameters: None 

Low Flow 

The flow sensor connected to the smart card has activated low 
flow protection. 
Related parameters: 30E, 30G, 30H, 31B, 31C, 31D, 36G 

Low Pressure 

The pressure sensor connected to the smart card has activated 
low pressure protection. 
Related parameters: 30A, 30C, 30D, 32D, 32E, 32F, 36E 

Low Water 

The depth sensor connected to the smart card has activated 
depth protection. 
Related parameters: 30L, 30N, 30O, 34A, 34B, 34C, 36I 

Motor Connection   
Motor Connection T1 
Motor Connection T2 
Motor Connection T3 

This trip is not adjustable. 
The motor is not connected correctly to the soft starter. 

•

 

Check individual motor connections to the soft starter for 
power circuit continuity. 

•

 

Check connections at the motor terminal box. 

•

 

If the soft starter is connected to a grounded delta mains 
supply, adjust parameter 20F 

Motor Connection

 to match the 

motor connection configuration. 

Related parameters: 20F 

Summary of Contents for EMX4i































































































































Reviews:

No comments