AuCom EMX4i Page 36 User Manual Download | Manualshive

Page: 36 / 126

background image

SETUP TOOLS

710-14888-00C EMX4i User Manual

35

5.4

Run simulation

The run simulation simulates a motor starting, running and stopping to confirm
that the soft starter and associated equipment have been installed correctly.

NOTE
The soft starter must be disconnected from mains voltage.
The simulation is only available when the soft starter is in Ready state.

To use the run simulation:
1.

Press MENU to open the menu then select Setup
Tools.

2.

Scroll to Run Simulation and press .

Run Simulation

Ready

Apply Start Signal

3.

Apply a start command from the selected
command source. The EMX4i simulates its
pre-start checks and closes the main contactor
relay. The Run LED flashes.

Run Simulation

Pre-Start Checks

MENU to Continue

NOTE
If mains voltage is connected, an error
message is shown.

Run Simulation

ATTENTION!

Remove Mains Volts

MENU to Continue

4.

Press . The EMX4i simulates starting. The Run
LED flashes.

Run Simulation

Starting X:XXs

MENU to Continue

5.

Press . The EMX4i simulates running.

Run Simulation

Running

Apply Stop Signal

6.

Apply a stop command from the selected
command source. The EMX4i simulates stopping.
The Run LED flashes.

Run Simulation

Stopping X:XXs

MENU to Continue

7.

Press . The Ready LED flashes and the main
contactor relay opens.

Run Simulation

Stopped

MENU to Continue

8.

Press . The EMX4i activates then deactivates
each programmable output.

Run Simulation

Prog Relay A

On

MENU to Continue

9.

Press to return to the Setup Tools.

«
...
34
35
36
37
38
...
»

Summary of Contents for EMX4i































































































































Reviews:

No comments

Related manuals for EMX4i

Brand: Sole Diesel Pages: 8

Brand: Mamas & Papas Pages: 16

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

Brand: OMC Pages: 18

Brand: Paradox Pages: 2

Brand: Paradox Pages: 2

FrameSaver 9120

Brand: Paradyne Pages: 20

VeriSafe VS2-NET

Brand: Panduit Pages: 6

Brand: Ublox Pages: 2

Brand: u-blox Pages: 19

Brand: WAGNER Pages: 60

GA Industries 930-DT

Brand: Vag Pages: 4

TBEN-L 8IOL Series

Brand: turck Pages: 148

APEXpy 07-37A2-2111/ 520Series

Brand: Bartec Pages: 98

Brand: Dejero Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands