manualshive.com logo in svg

Atmel AVR XMEGA D Series, Manual, Page: 241 / 331

Share
Download
Atmel AVR XMEGA D Series Manual Download Page 241

241

8210C–AVR–09/11

Atmel AVR XMEGA D

20.6

Register Description

20.6.1

CTRL – Control register

• Bit 7:6 – RESET[1:0]: Reset

These bits are used to reset the CRC module, and they will always be read as zero. The CRC
registers will be reset one peripheral clock cycle after the RESET[1] bit is set.

• Bit 5 – CRC32: CRC-32 Enable

Setting this bit will enable CRC-32 instead of the default CRC-16. It cannot be changed while the
BUSY flag is set. 

• Bit 4 – Reserved

This bit is unused and reserved for future use. For compatibility with future devices, always write
this bit to zero when this register is written.

• Bit 3:0 – SOURCE[3:0]: Input Source

These bits select the input source for generating the CRC. The selected source is locked until
either the CRC generation is completed or the CRC module is reset. CRC generation complete
is generated and signaled from the selected source when used with the flash memory.

Bit

7

6

5

4

3

2

1

0

+0x00

RESET[1:0]

CRC32

–

SOURCE[3:0]

CTRL

Read/Write

R/W

R/W

R/W

R

R/W

R/W

R/W

R/W

Initial  Value

0

0

0

0

0

0

0

0

Table 20-1.

CRC reset.

RESET[1:0]

Group configuration

Description

00

NO

No reset

01

—

Reserved

10

RESET0

Reset CRC with CHECKSUM to all zeros

11

RESET1

Reset CRC with CHECKSUM to all ones

Table 20-2.

CRC source select .

SOURCE[3:0]

Group configuration

Description

0000

DISABLE

CRC disabled

0001

IO

I/O interface

0010

FLASH

Flash

0011

—

Reserved for future use

0100

—

Reserved for future use

0101

—

Reserved for future use

Summary of Contents for AVR XMEGA D Series












































































































































































































































































































































Reviews:

No comments