ATLET A-Ergo, Service Manual

Page: 237 / 250

ATLET SERVICE MANUAL A-ERGO ATLET SERVICE MANUAL A-ERGO
g g
contactor opens and an error code is contactor opens and an error code is
shown. shown.
El Elec ectr tric ical al sy syst stem em / / Di Diag agno nosi sis a s and nd tr trou oubl ble e sh shoo ooti ting ng / E / Err rror or co code des s 10 10.5 .59 9
0 02 2A7 A78 8 V VA ACC CC NO NOT T
OK OK
This test is carried out when This test is carried out when
stationary. The reason for the alarm
stationary. The reason for the alarm
is that the voltage from the speed
is that the voltage from the speed
controller is 1 volt higher that the
controller is 1 volt higher that the
minimum value programmed in the
minimum value programmed in the
PROGRAM
PROGRAM V VACC function. ACC function.
a) Speed controller not correctly a) Speed controller not correctly
calibrated.
calibrated.
b) Speed controller defective.
b) Speed controller defective.
0 02A 2A79 79 IINC NCO ORR RRE ECT CT
START START
This alarm indicates that an This alarm indicates that an
incorrect start has been made.
incorrect start has been made.
a) Speed controller defective. a) Speed controller defective.
b) The driver has used the wrong
b) The driver has used the wrong
sequence during start up.
sequence during start up.
c) Defective cables.
c) Defective cables.
d) If the error persists, replace
d) If the error persists, replace
regulator.
regulator.
0 02 2A A8 80 0 F FO OR RW W + +
BACK BACK
This test is carried out all the time, This test is carried out all the time,
and means that double travel
and means that double travel
directions have been requested at
directions have been requested at
the same time.
the same time.
a) The driver has used the wrong a) The driver has used the wrong
sequence during start up.
sequence during start up.
b) Defective cables.
b) Defective cables.
c) If the error persists, replace
c) If the error persists, replace
regulator.
regulator.
0 02 2A8 A86 6 P PE EDA DAL WI L WIR RE E
KO KO
This error code indicates that there This error code indicates that there
is a fault in the cables to the speed
is a fault in the cables to the speed
controller potentiometer.
controller potentiometer.
Check the cabling to the speed Check the cabling to the speed
controller.
controller.
02 02A8 A89 9 PE PEV NO V NOT O T OK K Th The v e vol olta tage ge on P on PEV o EV out utpu put i t is n s not ot
correct. correct.
Replace regulator. Replace regulator.
0 02 2A A9 93 3 IIN NP PU UT T
ERROR #2 ERROR #2
This alarm is detected only at power This alarm is detected only at power
up. Meaning: The battery voltage
up. Meaning: The battery voltage
differs more than 20% compared to
differs more than 20% compared to
nominal value.
nominal value.
Check with a multimeter if the battery Check with a multimeter if the battery
voltage is really over or under the
voltage is really over or under the
mentioned thresholds.
mentioned thresholds.
If not, using the Zapi console, check
If not, using the Zapi console, check
the”BATTERY VOLTAGE” in the
the”BATTERY VOLTAGE” in the
tester menu.
tester menu.
If you find a mismatch between the If you find a mismatch between the
real battery voltage and the Zapi real battery voltage and the Zapi
console battery voltage, you should
console battery voltage, you should
tune it:
tune it:
Go into the adjustment menu. Make
Go into the adjustment menu. Make
sure that “
sure that “SET BA SET BATTERY TYPE” is TTERY TYPE” is
24V and then tune the “ADJUST 24V and then tune the “ADJUST
BATTERY” parameter to the correct
BATTERY” parameter to the correct
value. Then switch the truck off and
value. Then switch the truck off and
on.
on.
0 02A 2A94 94 C CU URR RR..SE SENS NS
KO KO
Er Errro or r iin n cu currrren ent t m met eter er ssy ysste tem. m. Re Rep pllac ace e rreeg gu ula lato torr..
Table 10.26 Table 10.26 Error codes, drive motor regulator, AC1 Error codes, drive motor regulator, AC1
E Errrro or r cco od de e iin nd diicca attiin ng g E Ex xp plla an na attiio on n C Ch heecck k//A Accttiio on n
M MD DII H Ha an nd d
terminal terminal
https://www.besttruckmanuals.com/