ATLET A-Ergo, Service Manual

Page: 194 / 250

ATLET SERVICE MANUAL A-ERGO ATLET SERVICE MANUAL A-ERGO
not function. This will not function. This will result in the motor result in the motor running very slowly and consuming maximum running very slowly and consuming maximum
power. Avoid running the motor in this state. power. Avoid running the motor in this state.
10 10.1 .16 6 El Elec ectr tric ical al sy syst stem em / D / Des esig ign a n and nd fu func ncti tion on / D / Dri rive ve mo moto tor r r reg egul ulat ator or, A , AC1 C1
Connector, specification, drive motor regulator AC1 Connector, specification, drive motor regulator AC1
The drive motor regulator has The drive motor regulator has three connectors with inputs and outputs three connectors with inputs and outputs
for valves, sensors, changer-over switches and programming tools. etc. for valves, sensors, changer-over switches and programming tools. etc.
Each connector pin is specified below, with where appropriate the
Each connector pin is specified below, with where appropriate the
voltage level in connected position.
voltage level in connected position.
Connector E1 (the figure shows the connector from t Connector E1 (the figure shows the connector from the cabling side). he cabling side).
Table 10.2 Table 10.2 Connector E1 drive motor regulator AC1 Connector E1 drive motor regulator AC1
P Piin n D Deessccrriip pttiio on n C Co om mm meen ntt
E E1 1..1 1 C Co on nttrro olllliin ng g o of f D Drriiv ve e cco on nttaacctto orr C Co on nttrro olllleed d tto o B B--
E E1 1..2 2 S Su up pp plly y tto o D Drriiv ve e cco on nttaacctto orr + +2 24 4V V
E E1 1..3 3 C Co on nttrro olllliin ng g o of f eelleeccttrriic c b brraak kee C Co on nttrro olllleed d tto o B B--
E E1 1..4 4 C Co on nttrro olllliin ng g o of f p pu um mp p cco on nttaacctto orr C Co on nttrro olllleed d tto o B B--
E E1 1..5 5 S u S up pp plly y tto o p pu ump mp cco on nttaacctto orr
E E1 1..6 6 C Co on nttrro olllliin ng g o of f v vaallv ve e ffo or r ssttrraad dd dlle e lliifftt C Co on nttrro olllleed d tto o B B--
E E1 1..7 7 C CA AN N cco om mm mu un niiccaattiio on n C CA AN N L Lo ow w
E E1 1..8 8 N Neeg g. . ssu up pp plly y tto o L Liifftt//L Lo ow weer r cco on nttrro oll B B--
E E1 1..9 9 P Po oss. . ssu up pp plly y tto o d drriiv ve e m mo otto or r een ncco od deerr + +4 4--5 5V V
E E1 1..1 10 0 N Neeg g. . ssu up pp plly y tto o d drriiv ve e m mo otto or r een ncco od deerr B B--
E E1 1..1 11 1 P Po oss. . ssu up pp plly y tto o iin nssttrru um meen ntt + +2 24 4V V
E E1 1..1 12 2 N Neeg g. . ssu up pp plly y tto o iin nssttrru um meen ntt B B--
E E1 1..1 13 3 IIn np pu ut t ffrro om m ssp peeeed d rreed du uccttiio on n ssw wiittcch h F Frro om m p prreessssu urre e ssw wiittcch h, , sseee e n no otte e b beello ow w ((* *))
E E1 1..1 14 4 IIn np pu ut t ffo or r lliiffttiin ng g o of f ssttrraad dd dlle e lliifftt + +2 24 4V V o on n aaccttiiv vaattiio on n
E E1 1..1 15 5 IIn np pu ut t ffo or r llo ow weerriin ng g o of f ssttrraad dd dlle e lliifftt + +2 24 4V V o on n aaccttiiv vaattiio on n
E E1 1..1 16 6 + +1 12 2V V ssu up pp plly y tto o iin nssttrru um meen ntt + +1 12 2V V
E E1 1..1 17 7 C CA AN N cco om mm mu un niiccaattiio on n C CA AN N H Hiig gh h
E1 E1.1 .18 8 Si Sign gnal al fr from om llif ift t ccon onttro roll
N Neeu uttrraal l = = aap pp prro ox x. . 2 2..5 5V V
M Maax l x liift ftin ing s g sp peeed ed = a = ap pp pro rox. x. 4 4.5 .5V V
Max Max lowe lowering ring spe speed ed = ap = approx prox. 1 . 1.0 V .0 V
E E1 1..1 19 9 IIn np pu ut t A A ffrro om m d drriiv ve e m mo otto or r een ncco od deerr S Sy yn ncch hrro on niissees s m mo otto or r d drriiv ve e w wiitth h p ph haassee
distorted pulses from the encoder distorted pulses from the encoder
E1 E1.2 .20 0 In Inpu put B f t B fro rom dr m driv ive mo e mottor or en enco code derr
(*) (*) The i The input nput fro from the m the pres pressur sure swi e switch i tch is filt s filtere ered so d so that that pre pressur ssure sur e surges wi ges will no ll not tri t trigge gger the r the
reduction of speed. A modified input value is required for at least 1 second to be reduction of speed. A modified input value is required for at least 1 second to be
t d N difi ti f th i t l i t d d i lifti d l i t d N difi ti f th i t l i t d d i lifti d l i
E1 E1
11 11
2 2 0 0 1 1 0 0
1 1
https://www.besttruckmanuals.com/