ATLET A-Ergo, Service Manual

Page: 101 / 250

ATLET SERVICE MANUAL A-ERGO ATLET SERVICE MANUAL A-ERGO
M Ma as st s t sy ys stte em m / / R Re ep pa aiir r iin ns sttrru uc cttiio on ns / s / F Fo orrk ks s 6 6..2 23 3
Forks Forks
Adjusting the lowest height on forged forks Adjusting the lowest height on forged forks
1. 1. The The inn inner er and and ou outer ter mas masts s ts shou hould b ld be l e lowe owere red. d.
2. 2. Adjus Adjust the tw t the two ou o outer lift ter lift chain chains so t s so that the hat the mast h mast hangs angs a littl a little fro e from the l m the lift ch ift chains. ains.
3. 3. Adjus Adjust the t the middl middle ch e chain s ain so that o that the f the fork h ork head ead is 5 ± is 5 ± 2 mm 2 mm from t from the gr he ground ound
(see (see figu figure re 6.27 6.27). ).
Adjusting the lowest height on welded forks Adjusting the lowest height on welded forks
1. 1. The The inn inner er and and ou outer ter mas masts s ts shou hould b ld be l e lowe owere red. d.
2. 2. Adjus Adjust the tw t the two ou o outer lift ter lift chain chains so t s so that the hat the mast h mast hangs angs a littl a little fro e from the l m the lift ch ift chains. ains.
3. 3. Adj Adjust t ust the c he chai hains s ns so tha o that the f t the fork h ork heig eight i ht is as s s as sho hown in t wn in tabl ablee 6.4 6.4..
Fork height in lowered position: Fork height in lowered position:
Fork test Fork test
Seven inspection points are included in the fork test. If the f Seven inspection points are included in the fork test. If the forks fail to meet any of the orks fail to meet any of the
points, the machine must be taken out of service. If the customer i points, the machine must be taken out of service. If the customer is not prepared to do s not prepared to do
this, it should be written in the r this, it should be written in the report that “The forks do not comply with the requirements eport that “The forks do not comply with the requirements
in SS-ISO/ 5057”. When the customer subsequently signs the service order, they bear the in SS-ISO/ 5057”. When the customer subsequently signs the service order, they bear the
responsibility for the defective forks.
responsibility for the defective forks.
Important! Important!
The truck must pass the fork test to comply with SS-ISO/5057. The truck must pass the fork test to comply with SS-ISO/5057.
Figure 6.27 Figure 6.27 Distance from floor Distance from floor
Table 6.4 Table 6.4 Height of forks over floor in rest position Height of forks over floor in rest position
M Ma asst t tty yp pee M Miin n M Ma ax x ((m mm m))
A A--E Errg go o 1 16 60 0 cco on nttrro olllleed d b by y g grro ou un nd d cclleeaarraan nccee 8 89 9
A A--E Errg go o 2 20 00 0 cco on nttrro olllleed d b by y g grro ou un nd d cclleeaarraan nccee 9 91 1
A A--E Errg go o T Teelleesscco op piic c ffo orrk ks s ((T TF F)) cco on nttrro olllleed d b by y g grro ou un nd d cclleeaarraan nccee 7 73 3
SM 075.1 SM 075.1
5 5
2 2
https://www.besttruckmanuals.com/