Atlantic WOYG112LHT Installation And Commissioning Instructions Download

Page: 42 / 92

5 .1 .7 Electrical connections on

the hydraulic module side

Access to the connector terminals

Remove the front panel.

Open the electrical cabinet.

Make the connections according to the diagram

(

figure 44 and figure 46

figure 43 -

Description of the hydraulic module's electrical cabinet

X10

X12

X13

X14

X15

X30

X50

X70

X75

X80

X82
X83

X84

Gas regulation board (LMS)

Manages the operation of the gas exchanger

(exchanger ignition, safety, regulation).

HP regulation board (RVS)

manages the whole appliance and

regulates the different heating circuits.

2 COM interfaces (OCI 345)

provide the communication between the

2 LMS and RVS boards and the transmission

of the climate data (slope, temperatures).

Interface board

provides the link with

the outdoor unit.

Connection terminal

Grommets (power)

Grommet (sensors)

Do not fit the sensor wires and the power supply wires

in parallel in order to avoid interferences due to the

voltage surges in the power supply.
Ensure that all of the electrical cables are housed in the

spaces provided.

Installation and commissioning instructions "1485 - EN"

Heat pump alféa hybrid duo gas

- 42 -

Summary of Contents for WOYG112LHT





























































































Search results

Summary of Contents for WOYG112LHT

Reviews:

Related manuals for WOYG112LHT

Brands by name

Popular brands

Atlantic WOYG112LHT, Installation And Commissioning Instructions

Search results

Summary of Contents for WOYG112LHT

Reviews:

Related manuals for WOYG112LHT

Brands by name

Popular brands