Atlantic WOYG112LHT Installation And Commissioning Instructions Download

Page: 45 / 92

figure 46 - Connections on the heat pump regulator (accessories and options)

X10

X12

X13

X14

X15

X30

X50

X70

X75

X80

X82
X83

X84

2 1

B2 M B1 3 2 1

2 1

3 2

X86

EX1

EX2

EX3

X11

X60

Room thermostat

T55**

Room

control unit

T75**

Wireless room

control unit

T78**

LMS

Load shedding or EJP function

(Peak Day

Erasure)

Tariffs, day/night, peak/off peak

(not concerned)

External fault

Outdoor contact

device*

(faults, load shedder,

energy meter)

* If the command does not supply a potential free contact, the contact must be relayed to obtain equivalent wiring.

In all cases, refer to the instructions for the external parts (load shedder, energy meters…) for the wiring.

** Option

T75 : Terminal 3 of the central ambient unit T75 does not need to be connected (central ambient unit lighting).

Outdoor

sensor

RVS

Wireless room

thermostat

T58**

Installation and commissioning instructions "1485 - EN"

- 45 -

Heat pump alféa hybrid duo gas

Summary of Contents for WOYG112LHT





























































































Search results

Summary of Contents for WOYG112LHT

Reviews:

Related manuals for WOYG112LHT

Brands by name

Popular brands

Atlantic WOYG112LHT, Installation And Commissioning Instructions

Search results

Summary of Contents for WOYG112LHT

Reviews:

Related manuals for WOYG112LHT

Brands by name

Popular brands