Atlantic WOYG112LHT Installation And Commissioning Instructions Download

Page: 75 / 92

Hydraulic module

: Flashing LED visible on the 3 in 1 interface board.

Outdoor unit

Error number

LED display

Error contents

LED 2 (green)

LED 1 (red)

1 Flash

Communication error between Hydraulic unit and Outdoor unit.

2 Flashs

3 Flashs

Connection forbidden (series error).

3 Flashs

1 Flash

Indoor unit power supply abnormal.

3 Flashs

2 Flashs

Serial communication error between Controller /Interface PCBs.

4 Flashes

1 Flash

Heat pump capacity signal error (Open or short).

4 Flashes

2 Flashes

Hydraulic unit heat-exchange thermistor Error.

6 Flashs

1 Flash

Outdoor unit power supply abnormal.

6 Flashs

2 Flashs

Outdoor unit main PCB error.

6 Flashes

3 Flashes

Inverter error.

6 Flashes

4 Flashes

Active filter error.

6 Flashs

5 Flashs

Outdoor unit IPM error.

6 Flashs

7 Flashs

Outdoor unit power short interruption error (protective operation).

6 Flashs

8 Flashs

Outdoor unit magnetic relay error.

7 Flashes

1 Flash

Discharge thermistor error.

7 Flashes

2 Flashes

Compressor thermistor error.

7 Flashes

3 Flashes

Heat-exchange thermistor (outlet / intermediate) error.

7 Flashes

4 Flashes

Outdoor thermistor error.

7 Flashs

Outdoor unit heat sink temp. thermistor error.

7 Flashes

8 Flashes

Expansion valve thermistor error.

8 Flashes

4 Flashes

Current sensor error.

8 Flashes

6 Flashes

Pressure sensor error / Pressure switch error.

9 Flashes

4 Flashes

Current trip

9 Flashes

5 Flashes

Detection of compressor position error / Compressor start up error.

9 Flashes

7 Flashes

Outdoor unit fan motor error.

10 Flashes

1 Flash

Discharge temperature protection.

10 Flashes

3 Flashes

Compressor temperature protection.

10 Flashs

4 Flashs

Outdoor unit pressure error.

10 Flashes

5 Flashes

Low pressure abnormal.

10 Flashs

9 Flashs

Current overload error.

Continuous flashing

(1 sec On / 1 sec Off)

Pump down operation.

Continuous

lighting

Off

Defrosting.

Installation and commissioning instructions "1485 - EN"

- 75 -

Heat pump alféa hybrid duo gas

Summary of Contents for WOYG112LHT





























































































Search results

Summary of Contents for WOYG112LHT

Reviews:

Related manuals for WOYG112LHT

Brands by name

Popular brands

Atlantic WOYG112LHT, Installation And Commissioning Instructions

Search results

Summary of Contents for WOYG112LHT

Reviews:

Related manuals for WOYG112LHT

Brands by name

Popular brands