ATEN VM0808HA User Manual Download Page 36

Page: 36 / 98

VM0808HA User Manual

Operation Mode

The EDID Mode, CEC, OSD and Output Status features can be configured
from the Operation Mode page.

EDID (Extended Display Identification Data) is used to have the
VM0808HA automatically apply a preset video configuration or EDID
Mode, which utilizes the best resolution across different monitors

Consumer Electronics Control (CEC) allows interconnected HDMI
devices to communicate and respond to one remote control

To configure the VM0808HA’s operation mode settings from the Main Screen,
use the

Menu

pushbutton to access the Menu page, press

Next

to navigate

to the next page, then press pushbutton

to access the Operation Mode page.

EDID Mode

To configure the EDID Mode, do the following:

1. From the Operation Mode page, press pushbutton

2. Press pushbuttons 1–4 to make your selection.

1: Operation Mode
2: Security Mode

8: Next

7: Back

1: EDID Mode
2: CEC

8: Next

1: Port 1

3: Remix

2: Default (In use)

4: Customized

Summary of Contents for VM0808HA



































































































Search results

Summary of Contents for VM0808HA

Reviews:

Related manuals for VM0808HA

Brands by name

Popular brands

ATEN VM0808HA, User Manual

Search results

Summary of Contents for VM0808HA

Reviews:

Related manuals for VM0808HA

Brands by name

Popular brands