manualshive.com logo in svg

Atal AWP-C, User Manual, Page: 58 / 82

Share
Download
Atal AWP-C User Manual Download Page 58

 
 

 

 

 

 
 

 

Error 37 

Unknow type of Digi probe. 

Please  update  firmware  version  and  after  that  detect  Digi 
probe(s) again. 

Error 38 

Communication error with memory for calibration data inside 
Digi probe. It is likely that Digi probe is not connected properly, 
or probe is damaged. 

Please  connect  properly  Digi  probe  or  replace  damaged 
probe. 

Error 39 

Memory  for  calibration  data  inside  Digi  probe  have  wrong 
CRC. 

Please follow procedure for Error 36. 

Error 40 

Connected  type  of  Digi  probe  is  not  same  as  was  detected 
probe. 

Please detect connected Digi probe(s) again. 

Error 50 

Device configuration for channel is damaged. 

Damaged  configuration  can  be  fixed  by  the  Factory  defaults 
procedure  or  using  WifiSensorUtility  which  can  be  obtained 
from technical support. 

Error 52 

Measured  value  cannot  be  shown  due  to  overflow  during 
conversion. 

Error 53 or n/a 

Value is not available. This error is shown at disabled channels 
or  when  value  was  not  measured  yet.  CO

2

  concentration  is 

available 15 sec after device start-up. 

Error 55 

This error is related to values transferred via Modbus TCP. It 
signalises overflow of Modbus register. 

 

Warning exclamation mark on LCD 

Warning  exclamation  mark  shown  on  left  bottom  corner  of  LCD  display 
signalise issue with device itself. Main reasons for this warning are: 

•

  Hardware  issue  with  one  of  these  components 

–  WiFi  coprocessor, 

internal memory chip, RTC chip or LCD driver chip. 

•

  Damaged content of configuration memory. 

Damaged  content  of  configuration  memory  can  be  identified  by  warning 
message in case of attempt to device setup. Damaged content can be fixed 
by the 

Factory defaults procedure

 or using WifiSensorUtility. This software 

can be obtained from technical support. 

In case of issue with hardware, please contact technical support directly. 

 

 

Summary of Contents for AWP-C



















































































Reviews:

No comments