manualshive.com logo in svg

Atal AWP-C, User Manual, Page: 55 / 82

Share
Download
Atal AWP-C User Manual Download Page 55

 
 

 

 

 

 
 

 

 

 

55 

Troubleshooting 

Factory defaults 

By the factory defaults procedure, the device is restored into same state as 
was newly purchased. Current device settings are lost including passwords 
and WiFi connection parameter. Provisioning procedure for connecting into 
WiFi network needs to be done again. Factory default procedure can be done 
locally only. Lid of device needs to be disassembled using screwdriver Torx 
T10. This screwdriver is not a part of shipment.  

Factory defaults procedure: 

1.  Remove device power supply by disconnecting USB-C connector. 

2.  Unscrew four Torx screw and open device lid. 

3.  Change jumper position from Position 1 to Position 2 as shown at image 

below. For changing jumper position may to be used tweezers. 

 

4.  Connect power supply by the USB-C connector. 

5.  Wait till be shown text DEF1 DONE at LCD display. 

6.  Disconnect power supply. 

7.  Move jumper back to Position 1. 

8.  Close device lid and put back all four screws. 

9.  Power on device. Factory defaults restore procedure was accomplished. 

Factory defaults procedure restore configuration of device itself. Calibration 
constants inside Digi probes and device are not changed. Device calibration 
can be restored by modified factory default procedure. Before you power on 
device  (point  4),  you  need  to  press  and  hold  button  SET.  Button  can  be 
released  while  text  DEF2  DONE  is  shown.  Other  steps  are  same  as  at 
procedure above. 

 

Summary of Contents for AWP-C



















































































Reviews:

No comments