manualshive.com logo in svg

Atal AWP-C, User Manual, Page: 33 / 82

Share
Download
Atal AWP-C User Manual Download Page 33

 
 

 

 

 

 
 

 

 

 

33 

 

Local IP address of the WiFi sensors can be discovered by ways described 
at chapter 

Troubleshooting

. 

AP mode 

AP mode is intended for device provisioning and for a first setup. WiFi sensor 
comes into AP mode when SSID for WiFi client mode is blank. Device can 
be switched into AP mode by the device buttons manually if needed. When 
device  is  switched  into  AP  mode  by  buttons  and  there  is  no  other 
communication  with  WiFi  sensor,  device  is  switched  back  to  client  mode 
automatically after 10 minutes. 

SSID,  security  and  channel  number  can  be  changed  according  needs.  By 
the default, SSID contains device serial number and WiFi network security is 
not  used.  It  is  recommended  to  enable  security  for  AP  mode  to  prevent 
unauthorised access to the device. WiFi channel number can be changed to 
prevent interferences with other WiFi networks if needed. 

Summary of Contents for AWP-C



















































































Reviews:

No comments