manualshive.com logo in svg

Atal AWP-C, User Manual, Page: 12 / 82

Share
Download
Atal AWP-C User Manual Download Page 12

 
 

 

 

 

 
 

 

Features 

LCD display 

WiFi sensors are equipped with LCD display for showing current measured 
values  and  device  state  information.  Showing  of  measured  values  at  LCD 
display  can  be  enabled  for  each  value  separately.  When  LCD  display  is 
deactivated  and  buttons  are  pressed,  LCD  display  is temporarily  activated 
with  status  information.  LCD  display  backlight  is  configurable  into  one  of 
three modes (off, always on or when key is pressed). 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Feature 

Description 

Current measured value(s) 

Current measured value at device channel. Units 
and  value  position  at  LCD  display  depends  on 
each  measured  value.  Measured  value  position 
at  display  is  not  configurable  by  end-user. 
Screens with measured values are switched with 
interval 4 sec. 

Alarm at measured value 

 

Alarm  state  (Alarm  1  or  Alarm  2)  at  measured 
value is signalised by “bell” icon before measured 
value. 

Alarm state 

 

Signalisation  if  there  is  any  alarm  on  device. 
Alarm state comes from alarms on channel(s) or 
from  system  alarms. 

System  alarms

  are 

designed for diagnostic of the device failure. 

Summary of Contents for AWP-C



















































































Reviews:

No comments