manualshive.com logo in svg

Atal AWP-C, User Manual, Page: 31 / 82

Share
Download
Atal AWP-C User Manual Download Page 31

 
 

 

 

 

 
 

 

 

 

31 

System alarms 

System  alarms  are  used  to  diagnose  functionality  of  measurement  chain 
including device or connected probes. A system alarm notifies about failure 
of  the  device  including  connected  probes.  On  the  other  hand,  alarms  on 
measurement  values  indicate  an  issue  with  technology  monitored  by  the 
device.  System  alarms  may  to  be  intended  for  different  person  than  is 
responsible for alarms from measured values. 

There are three system alarms. System alarm from measurement error on 
channel, system alarm from configuration error, and error from RTC battery. 
System alarm from measurement error is activated in case error state on any 
of channels occurs and this error persists for selected delay. Acoustic and 
LED signalisation can be used in case of system alarm if needed. Device has 
capability to send alarm email in case system alarm. 

 

 

 

Summary of Contents for AWP-C



















































































Reviews:

No comments