ASTRO-MED QLS-2000XE SERIES Operation & Setup Manual Download Page 54

Page: 54 / 214

3-18

Keypad Controls and Menus

TTR Sensor

This function is for use by authorized technicians when performing
diagnostics at the factory. In general use, the TTR Sensor should always be
On.

To enable/disable the TTR sensor:

Press the MENU key. Use the arrow keys to select Mode from the menu
and then press the SELECT key.

In the MODE menu, use the arrow keys to select TTR Sensor. Then press
the SELECT key.

Note:

The printhead names will vary based on the printer model.

Press the up/down arrows to turn the TTR Sensor on or off. Use the
left/right arrows to move to the next printstation.

Caution:

This capability is intended for factory diagnostics only. Do not turn

off the sensor. Use of the printer with the ribbon sensor disabled could result
in damage to the printhead (due to overheating) and/or poor print quality.

(MODE) Cutter | Mirror | > TTR Sensor
Front: On Bottom: On Rear: On

| Intensity | Print | Memory | >

Mode |

Summary of Contents for QLS-2000XE SERIES























































































































































































































Search results

Summary of Contents for QLS-2000XE SERIES

Reviews:

ASTRO-MED QLS-2000XE SERIES, Operation & Setup Manual, Page: 54 / 214

Search results

Summary of Contents for QLS-2000XE SERIES

Reviews: