54
Rev 2, 18.06.19
This limited warranty covers all standard plug-in cabinets and walk-in units up to 800kg maximum load. Arredo Inox Srl
warranties its equipment to the original purchaser against defects in materials or workmanship for a period of one year
from the date of installation. This limited warranty is not transferable. Warranties for parts and labor last one year, If service
work is carried out under Limited Warranty, this will not extend the Limited Warranty period for the unit, or for the new
parts. The warranty is voided by improper placement/storage, use, or when used in ambient temperatures exceeding
32
oC / 89oF, please refer to user/instructional manual for further details. The warranty period begins on the date of instal-
lation, after validating the warranty by sending an e-mail to the following address
enclosing the installation worksheet, and applies only if the purchaser has not violated any of the exclusions or limitations
listed below.
What is not covered under this Limited Warranty
• Normal wear and tear;
• Deliberate or negligent damage, damage caused by failure to observe operating instructions, incorrect installation
or by connection to the wrong voltage, damage caused by chemical or electro-chemical reaction, rust, corrosion or
water damage including but not limited to damage caused by excessive minerals in the water supply, damage caused
by abnormal environmental conditions;
• Consumable parts, these include, but are not limited to: light bulbs, bulb enclosures, batteries, fuses, and gaskets;
• Non-functional and decorative parts, which do not affect normal use of the appliance, including any scratches and
possible color differences;
• Any build up of scale/calcium a) in and/or around the lines leading into or exiting the Fumotic®, b) within the
Fumotic® itself;
• Accidental damage caused by foreign objects or substances and cleaning or unblocking of filters, drainage systems;
• Charges for service calls resulting in a diagnosis of equipment that was properly operating including, but not limited
to: diagnosing equipment operation in a defrost mode, rest/recovery period, air cycling period, air exchange period, or
power to the equipment was disconnected or interrupted, or that was shut down by over current or high/low pressure
controls, or that the indicating temperature or humidity device was incorrectly calibrated;
• Failures caused by a) alteration/modifications or parts installed but not authorized by manufacturer, b) abuse and/
or misuse of equipment, c) failure to provide adequate air flow around condenser and/or evaporator air coils, and/or
d) failures caused by environmental effects and/or outside influences, including but not limited to fire damage, smoke
damage, or explosions;
• Cleaning debris or removing ice from a heat transfer surface, not caused by a defect in materials and workmanship;
• The replacement of refrigerant without evidence of a leak in the system components;
• Adjustments of any operation control such as the thermostatic expansion valve, defrost components, pressure, oil
safety, or temperature thermostat/controller;
• Repairs not carried out by our appointed service providers and/or an authorized service contractual partner or where
non-original parts have been used;
• Repairs caused by installation, which is faulty or not according to specification;
• Transportation damages of any kind;
• Cost for carrying out the initial installation of the unit;
Due to the fact that Maturmeat® uses programs that are modifiable by it’s operator, Arredo Inox srl accepts no
responsibility for product loss, spoilage, unsafe/unhealthy or unsanitary products produced in the Maturmeat®. Please
carefully read the instructional manual before attempting to install your unit to avoid injury and to ensure proper
installation. Thoroughly inspect your unit after unpacking and report any damage during transit to your local area dealer,
distributor, reseller, agent, etc. and transport company. All warranty claims must be made to the local area dealer, dis-
tributor, reseller, agent, etc. In the case where the unit is purchased directly from the manufacturer all warranty claims
must be made to
. Any repair or replacement of a covered component may be
made with a functionally equivalent component, as determined by Arredo Inox Srl.
Installed in the electronic control settings, default recipes and climatic variables of operation are to be considered
indicative and otherwise be changed and / or user programmable in case of damage and / or failure of the food
content in the machine as a result of execution the same, the manufacturer cannot be held responsible, civil and / or
criminal and may not be charged at the same in anyway.
Humidity and Temperature Sensors/ Probes:
The probes in each Maturmeat® used should calibrated with a certified instrument and by trained personnel, all probes
installed on the machines are very sensitive, it is recommended that they be calibrated each time a new production
lot is started. Each unit is thoroughly tested before shipment, any inaccuracies or operating problems before and after
the installation must be reported to the manufacturer within the first 8 days to ensure proper function, the manufacturer
cannot be held liable in such case.
pH Probe Storage:
The probes should be stored in a protective capsule or in a container with their membranes immersed in a
3M KCI solution. The storage temperature should be between 10°/30°C, and never below -5°C. In case of loss of the
protective capsule during transport or storage, the KCI could be removed easily by rinsing the probe in water. The probe
will not suffer any consequences from this loss. The electrode must always be kept in its storage capsule filled with the
corresponding electrolytic solution. The sensitive membrane should never be dry. If you do not have electrolyte solution,
you can submerge the electrode in pH 4 buffer solution. Never store the electrode in distilled water.
Arredo Inox Srl is the exclusive licensed manufacturer of the patents from Alessandro Cuomo Brevetti Milano
LIMITED WARRANTY
5.1
Summary of Contents for Maturmeat 100
Page 1: ...1 Rev 2 18 06 19 Maturmeat Manual...
Page 56: ...56 Rev 2 18 06 19...
