Arctic Cat 2014 400 Service Manual Download | Manualshive

Page: 107 / 124

background image

104

CC875

CC876

6. Using the Pinion Gear/Shaft Removal Tool and a

hammer, remove the pinion gear from the gear case
housing.

CC878

7. Secure the pinion gear in a bearing puller; then

remove the pinion bearing using a press. Account for
a collar and a bearing.

CC879



NOTE: If gears are being replaced, use the existing

shims.



NOTE: If the gear case housing is being replaced,

proceed to the following Shimming Procedure/Shim
Selection sub-section.

Shimming Procedure/Shim
Selection

It is very important to adjust bevel gears for the proper
running tolerances. Gear life and gear noise are greatly
affected by these tolerances; therefore, it is very impor-
tant to properly adjust any gear set prior to final assem-
bly.

The following procedure can be used on both front differ-
ential or rear drive gear case.



NOTE: All bearings must be installed in the gear

case and the pinion properly installed before pro-
ceeding.

Backlash



NOTE: Always set backlash prior to any other shim-

ming.

1. Install the existing shim or a 0.051-0.055-in. shim on

the gear case side of the ring gear assembly.

GC031A

2. Install the ring gear with shim in the gear case; then

while holding the pinion stationary, rock the ring
gear forward and back to determine if any backlash
exists. If no backlash exists, install a thicker shim
and recheck.

Shims

p/n

mm

in.

0402-405

1.3

0.051

0402-406

1.4

0.055

0402-407

1.5

0.059

0402-408

1.6

0.063

0402-409

1.7

0.067

«
...
105
106
107
108
109
...
»

Summary of Contents for 2014 400





























































































































Reviews:

No comments

Related manuals for 2014 400

Brand: E-TON Pages: 30

Brand: Labrie Pages: 172

Brand: Suzuki Pages: 477

Utility Vehicle Workshop

Brand: Bush Hog Pages: 11

Brand: Vermeer Pages: 88

Brand: Can-Am Pages: 144

Brand: PRONAR Pages: 101

BOX LINER TU 70

Brand: Krone Pages: 92

Brand: TrailMaster Pages: 7

Brand: TrailMaster Pages: 22

2014 RZR XP 1000

Brand: Polaris Pages: 474

ST SHUTTLE 4/6 E 2008

Brand: E-Z-GO Pages: 66

Brand: CAMSO Pages: 11

Brand: Etnyre Pages: 64

Brand: Razor Pages: 12

Brand: FORS MW Pages: 13

Brand: Honda Pages: 65

2009 Ranger RZR

Brand: Polaris Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands