Arctic Cat 2014 400 Service Manual Download

Page: 117 / 124

114

PR713A

PR715

7. Using an appropriate seal removal tool, carefully

remove the seals from the brake caliper housing;
then remove four O-rings from the brake caliper
housing noting the location of the different sized
O-rings. Discard all seals, O-rings, and crush wash-
ers.

CLEANING AND INSPECTING

1. Clean all caliper components (except the brake pads)

with DOT 4 brake fluid. Do not wipe dry.

2. Inspect the brake pads for damage and excessive

wear.



NOTE: For measuring brake pads, see Periodic

Maintenance - Hydraulic Brake Systems.

3. Inspect the brake caliper housings for scoring in the

piston bores, chipped seal ring grooves, or signs of
corrosion or discoloration.

4. Inspect the piston surface for scoring, discoloration,

or evidence of binding or galling.

5. Inspect the caliper holder for wear or bending.

ASSEMBLING/INSTALLING

1. Install new seals into the brake caliper housing and

apply a liberal amount of DOT 4 brake fluid to the
cylinder bore of the housing, seals, and brake piston.

PR715

PR717A

2. Press the piston into the caliper housing using hand

pressure only. Completely seat the piston; then wipe
off any excessive brake fluid.

PR711A

PR712

3. Apply high-temperature silicone grease (supplied

with the O-ring kit) to the inside of the caliper holder
bores and O-rings; then install the four O-rings into
the caliper.

! WARNING

Make sure to hold the towel firmly in place or the piston
could be ejected from the housing causing injury.

CAUTION

Make sure the seals are properly in place and did not
twist or roll during installation.

Summary of Contents for 2014 400





























































































































Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands

Arctic Cat 2014 400, Service Manual

Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands