Arctic Cat 2014 400 Service Manual Download | Manualshive

Page: 116 / 124

background image

113

3. Bleed the brake system (see Periodic Maintenance -

Hydraulic Brake Systems).

Hydraulic Brake Caliper

REMOVING/DISASSEMBLING

1. Secure the ATV on a support stand to elevate the

wheel; then remove the wheel.

2. Drain the brake fluid from the caliper, hose, and mas-

ter cylinder through the bleed screw by pumping the
brake lever/pedal.

PR235



NOTE: Whenever brake components are removed,

disassembled, or repaired where brake fluid is
exposed to air, drain all fluid and replace with new
DOT 4 brake fluid from an unopened container. Brake
fluid readily absorbs moisture from the air signifi-
cantly lowering the boiling point. This increases the
chance of vapor lock reducing braking power and
increasing stopping distance.

3. Remove the brake hose from the caliper and close

the bleed screw; then remove the caliper.

4. Compress the caliper holder against the caliper

(opposite the O-ring side) and remove the outer
brake pad; then remove the inner brake pad.



NOTE: If brake pads are to be returned to service,

do not allow brake fluid to contaminate them.

PR237A

PR238

5. Remove the caliper holder from the caliper and dis-

card the O-ring.

PR239B



NOTE: The O-ring is used for shipping purposes

and provides no function in operation.

6. Cover the piston end of the housing with a shop

towel; then keeping fingers clear of piston travel,
apply compressed air to the fluid port to blow the
piston free of the housing. Account for two seal rings
in the housing.

! WARNING

Arctic Cat recommends that only authorized Arctic Cat
ATV dealers perform hydraulic brake service. Failure to
properly repair brake systems can result in loss of con-
trol causing severe injury or death.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

! WARNING

Never let brake fluid contact the eyes. Damage to the
eyes will occur. Always wear appropriate protective
safety goggles and latex gloves when handling brake
fluid.

CAUTION

Brake fluid is highly corrosive. Do not spill brake fluid
on any surface of the ATV and do not reuse brake fluid.

«
...
114
115
116
117
118
...
»

Summary of Contents for 2014 400





























































































































Reviews:

No comments

Related manuals for 2014 400

Brand: Yutrax Pages: 10

2005 TRX400EX Sportrax 400EX

Brand: Honda Pages: 238

Brand: Honda Pages: 250

Brand: E-TON Pages: 118

Brand: Komatsu Pages: 4

Brand: Ski-Doo Pages: 159

Brand: Ski-Doo Pages: 103

Brand: TGB Pages: 269

Brand: TGB Pages: 306

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 92

WARRIOR YFM350XN

Brand: Yamaha Pages: 167

Brand: Yamaha Pages: 227

Brand: Yamaha Pages: 288

Brand: Yamaha Pages: 360

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands