Arctic Cat 2014 400 Service Manual Download | Manualshive

Page: 99 / 124

background image

96



NOTE: If the meter showed no voltage, inspect

ground connections, starter motor lead, battery volt-
age (at the battery), starter relay, or the neutral start
relay.

REMOVING

1. Disconnect the battery.

2. Remove the nut securing the positive cable to the

starter; then remove the cable from the starter.

3. Remove the two cap screws securing the starter to

the crankcase; then remove the starter. Account for
an O-ring.

INSTALLING

1. Apply a small amount of grease to the O-ring seal on

the starter; then install the starter into the crankcase.
Secure with two cap screws making sure the engine
ground is secured by the rear cap screws. Tighten to
8 ft-lb.

KC201A

2. Secure the positive cable to the starter with the nut.

Tighten to 8 ft-lb.

3. Connect the battery.

CDI Unit

The CDI is located on the electrical tray in front of the
steering post.



NOTE: The CDI unit is not a serviceable component.

If the unit is defective, it must be replaced.

The CDI is rarely the cause for electrical problems; how-
ever, if the CDI is suspected, substitute another CDI unit
to verify the suspected one is defective.



NOTE: Prior to replacing the CDI unit to assure the

CDI unit is defective, it is advisable to perform a CDI
peak voltage test (see Ignition Coil in this section)
and/or perform a continuity test of the wiring harness
from the CDI connector to the CDI unit.

Regulator/Rectifier

The regulator/rectifier is located under the front rack and
front fenders above the oil cooler.

TESTING

1. Start engine and warm up to normal operating tem-

peratures; then connect a multimeter to the battery as
follows.

2. Select the DC Voltage position; then connect the red

tester lead to the positive battery post and the black
tester lead to the negative battery post.

3. Start the engine and slowly increase RPM. The volt-

age should increase with the engine RPM to a maxi-
mum of 15.5 DC volts.



NOTE: If voltage rises above 15.5 DC volts, the reg-

ulator is faulty or a battery connection is loose or cor-
roded. Clean and tighten battery connections or
replace the regulator/rectifier. If voltage does not rise,
check Voltage (Charging Coil - No Load) in this sec-
tion. If charging coil voltage is normal, replace the
regulator/rectifier.

Lights

HEADLIGHTS - RUNNING LIGHTS

The connectors are the two 4-pin ones snapped onto the
front body/rack support. To release the connectors from
the frame, press the release tab with a small screwdriver.

KC224

CAUTION

Always disconnect the negative battery cable from the
battery first; then disconnect the positive cable.

«
...
97
98
99
100
101
...
»

Summary of Contents for 2014 400





























































































































Reviews:

No comments

Related manuals for 2014 400

Standard Pedal-Kart

Brand: DINO CARS Pages: 4

Brand: Suzuki Pages: 502

Brand: Seizmik Pages: 10

Brand: RIDGID Pages: 40

Brand: Bluewheel Pages: 50

Brand: Tomberlin Pages: 151

Brand: JI-EE Pages: 61

Brand: E-Z-GO Pages: 114

Brand: Yamaha Pages: 54

Brand: YX Motors Pages: 159

Ditch Witch PR482

Brand: Charles Machine Works Pages: 6

Brand: Yamaha Pages: 126

Brand: HAUL MASTER Pages: 2

Cargo Compact Series

Brand: Peecon Pages: 64

TrailMaster MINI

Brand: GOKARTS USA Pages: 5

Brand: GoKa Sports Pages: 46

Brand: Arctic Cat Pages: 156

Brand: Taylor-Dunn Pages: 232

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands