Arctic Cat 2014 400 Service Manual Download

Page: 89 / 124

KC219A

6. Install the fuel shut-off valve knob; then turn the

valve to the ON position.

7. Install the side panels and seat making sure they lock

securely in place.

Oil Filter/Oil Pump



NOTE: Whenever internal engine components wear

excessively or break and whenever oil is contami-
nated, the oil pump should be replaced. The oil pump
is not a serviceable component.

Testing Oil Pump

Pressure

1. Connect the Tachometer to the engine or place the

gauge in diagnostic mode and select “tACH.”

2. Connect the Oil Pressure Test Kit to the oil filter

drain plug.

KC195A

KC267



NOTE: Some oil seepage may occur when installing

the oil pressure gauge. Wipe up oil residue with a
cloth.

3. Warm up the engine to normal operating temperature

(cooling fan cycling); then increase engine RPM to
3000 RPM. The oil pressure must read 1.1-1.7
kg/cm

(16-25 psi).

KC268



NOTE: If the oil pressure is lower than specified,

check for low oil level, defective oil pump, or
restricted oil cooler.



NOTE: If the oil pressure is higher than specified,

check for clogged oil passage, clogged oil filter, or
improper installation of the oil filter.

Summary of Contents for 2014 400





























































































































Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands

Arctic Cat 2014 400, Service Manual

Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands