Arctic Cat 2014 400 Service Manual Download

Page: 63 / 124

MD1017

16. Remove the snap ring holding the oil pump driven

gear.

MD1019



NOTE: Always use a new snap ring when installing

the oil pump driven gear.

17. Remove oil pump driven gear. Account for the drive

pin and thrust washer.

MD1020

18. Remove three screws holding the oil pump and

remove the oil pump. Account for two alignment
pins.

MD1060

Servicing Right-Side

Components

INSPECTING CENTRIFUGAL
CLUTCH SHOE

1. Inspect the clutch shoe for uneven wear, chips,

cracks, or discoloration.

2. Inspect the depth of the grooves in the clutch shoes.

If any shoe is worn to the bottom of the groove,
replace the complete set.

ATV1014

INSPECTING CENTRIFUGAL
CLUTCH HOUSING

1. Inspect the clutch housing for burns, marks, scuffs,

cracks, scratches, or uneven wear.

2. If the housing is damaged in any way, the housing

must be replaced.



AT THIS POINT

To service clutch components, see Servicing Right-Side

Components sub-section.



AT THIS POINT

To service center crankcase components only, proceed

to Separating Crankcase Halves.

CAUTION

Always replace clutch shoes as a complete set or
severe imbalance could occur.

Summary of Contents for 2014 400





























































































































Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands

Arctic Cat 2014 400, Service Manual

Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands