Arctic Cat 2014 400 Service Manual Download

Page: 100 / 124

KC223

Voltage (Headlights)



NOTE: Perform this test on the main harness side of

the connectors. Also, the ignition switch must be in
the LIGHTS position.

1. Set the meter selector to the DC Voltage position.

2. Connect the black tester lead to the black wire; then

connect the red tester lead to the white wire.

3. With the dimmer switch in the LO position, the

meter must show battery voltage.

4. Remove the red tester lead from the white wire and

connect to the lavender wire.

5. With the dimmer switch in the HI position, the meter

must show battery voltage.



NOTE: If battery voltage is not shown in any test,

inspect the fuses, battery, main wiring harness, con-
nectors, or the left handlebar switch.

Voltage (Running Lights)

1. Release the wire connector from the frame; then

release and separate the connectors.



NOTE: Perform this test on the wiring harness side

of the connectors.

2. Connect the black tester lead of the meter to the

black wire; then with the tester in the DC Volts posi-
tion, connect the red tester lead to the brown/black
wire.

3. Turn the ignition switch to the LIGHTS position.

The meter must show battery voltage.



NOTE: If the meter does not show voltage, inspect

the LIGHTS fuse, battery connections, or trouble-
shoot the main wiring harness.

TAILLIGHTS - BRAKELIGHTS
Voltage (Taillights)



NOTE: Perform this test on the main harness side of

the connector. Also, the ignition switch should be in
the LIGHTS position.

1. Set the meter selector to the DC Voltage position.

2. Connect the black tester lead to the black wire; then

connect the red tester lead to the brown/blue wire.

3. The meter must show battery voltage.



NOTE: If the meter does not show voltage, inspect

fuses, wiring harness, connectors, and switches.

Voltage (Brakelights)



NOTE: Perform this test on the main harness side of

the connector. Also, the ignition switch should be in
the ON position and the brake (either foot pedal or
hand lever) must be applied.

1. Set the meter selector to the DC Voltage position.

2. Connect the black tester lead to the black wire; then

connect the red tester lead to the green/yellow wire.

3. The meter must show battery voltage.



NOTE: If the meter does not show voltage, inspect

bulb,

fuses,

wiring

harness,

connectors,

and

switches.

BACK-UP LIGHTS

The connectors are located on the rear frame supports
attached by a metal tab. They may be released from the
frame by depressing the release with a small screwdriver.

KC279

KC280

Voltage

1. Release the wire connectors from the frame; then

disconnect the connectors.



NOTE: Perform this test on the main harness side of

the connectors.

2. Connect the black tester lead to the brown/lavender

wire; then connect the red tester lead to the laven-
der/red wire.

Summary of Contents for 2014 400





























































































































Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands

Arctic Cat 2014 400, Service Manual

Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands