Arctic Cat 2014 400 Service Manual Download

Page: 61 / 124

MD1036

. Remove the V-belt.

MD1118

6. Remove the fixed drive face.

MD1094

Remove the nut holding the driven pulley assembly;
then remove the driven pulley assembly.

MD1068

8. Using an impact screwdriver, remove the three Phil-

lips-head cap screws holding the air intake plate.
Remove the air intake plate.

MD1092

9. Remove the cap screws holding the clutch cover onto

the right-side crankcase half. Note the positions of
the different-lengthed cap screws for installing pur-
poses

10. Using a rubber mallet, loosen

the clutch cover;

then

pull it away from the right-side crankcase half.

Account for two alignment pins and gasket.

MD1115

D. Centrifugal Clutch Assembly
E. Oil Pump Drive Gear
F. Oil Pump Driven Gear
G. Oil Pump



NOTE: Steps 1-10 in the preceding sub-section

must precede this procedure.



AT THIS POINT

Remove the cap screw holding the gear position switch
onto the right-side crankcase half; then remove the gear
position switch. Account for a spacer.

Summary of Contents for 2014 400





























































































































Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands

Arctic Cat 2014 400, Service Manual

Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands