Arctic Cat 2014 400 Service Manual Download

Page: 31 / 124

8. Tap the ball joint end out of the knuckle; then

remove the knuckle.

9. Remove the snap ring from the knuckle; then remove

the bearing.

PR287A

PR288

CLEANING AND INSPECTING

1. Clean all knuckle components.

2. Inspect the bearing for pits, gouges, rusting, or pre-

mature wear.

3. Inspect the knuckle for cracks, breaks, or porosity.

4. Inspect threads for stripping or damage.

ASSEMBLING AND INSTALLING

1. Install the bearing; then install the snap ring making

sure it seats into the knuckle.

PR287A

2. Install the knuckle to the upper and lower ball joints

and secure with the two cap screws. Tighten to 35
ft-lb.

KC313A

3. Install the tie rod end and secure with the nut.

Tighten to 30 ft-lb; then install a new cotter pin and
spread the pin.



NOTE: During assembling, new cotter pins should

be installed.

4. Apply a small amount of grease to the hub splines.

5. Install the hub assembly onto the splines of the shaft.

6. Secure the hub assembly with the nut. Tighten only

until snug.

KC305

7. Secure the brake caliper to the knuckle with the

“patch-lock” cap screws. Tighten to 20 ft-lb.

CAUTION

Use extreme care when removing the bearing. If the
bearing is allowed to fall, it will be damaged and will
have to be replaced.

Summary of Contents for 2014 400





























































































































Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands

Arctic Cat 2014 400, Service Manual

Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands