Arctic Cat 2014 400 Service Manual Download

Page: 84 / 124

KC0028A



NOTE: Turn the pilot screw clockwise until it is

lightly seated; then turn it counterclockwise the rec-
ommended number of turns as an initial setting.



NOTE: Note the locations of the jets and holder dur-

ing assembling procedures.

CC761A

3. Install the starter jet and slow jet. Tighten securely.

KC0032A

4. Install the main jet into the needle jet holder and

tighten securely; then install the needle jet and nee-
dle jet holder assembly into the carburetor and
tighten securely.

KC0031

KC0030A

5. Place the float assembly (with float valve) into posi-

tion and secure to the carburetor with the float pin.

KC0024



NOTE: Check float height by placing the carburetor

on its side w/float contacting the needle; then mea-
sure with a caliper the height when the float arm is in
contact with the needle valve. Float arm height
should be 17 mm.

Summary of Contents for 2014 400





























































































































Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands

Arctic Cat 2014 400, Service Manual

Search results

Summary of Contents for 2014 400

Reviews:

Related manuals for 2014 400

Brands by name

Popular brands