FORTY 5500
-
13
-
OPERATOR FOR SWING GATES
English
DESCRIPTION OF THE OPERATOR
1.
Envisaged use and Field of application
1.1
Hydraulic operator designed for the automation of swing
•
gates with double or single leaf, compatible with the follow
technical features and technical data of
tab.1
.
It is necessary that the gate has mechanical limit
stroke ashore.
The
fi
eld of application is limited to gates used for
•
intensive and continuous residential shared use; the
operator use does not exceed the maximum daily
cycles in the technical speci
fi
cations.
All other uses are considered improper and therefore
hazardous.
All other uses are considered improper and hazardous,
therefore is not authorized by
Aprimatic
.
Caution
The operator does not form part of the support or safety
system of the gate; the gate should already have ade-
quate safety and support features.
Do not use the product for purposes other than those
speci
fi
ed.
Do not tamper with or modify the product.
The product must only be installed using APRIMATIC
accessories.
Technical features
1.2
The operator uses an electric pump and a hydraulic
piston to transmit the motion to the gate.
It is available in the product versions described in
tab.2
,
with the following features.
Irreversibility by Hydraulic lock
(
feature related to
product version
) : ensuring the stop of the gate while the
engine is not running.
The non-reversible motor doesn't prevent intrusions.
Emergency manual release
(in all product versions)
:
with release key for manual operation in the event of
power failure.
Limitation of thrust force
: by-pass adjustable valves.
Relevant control unit:
Aprimatic SWING 230
.
i
Do NOT use other type of control unit.
Aprimatic
S.p.A.
doesn't assume liability for the failure to
meet those recommendations.
For the
technical data
, see the relevant table.
IMPORTANT
: The noise level of the operator, released
from the wing and the pillar, is within the maximum limits
established by EU regulations.
IMPORTANT
: the peripheral speed of the gate to be set
must be identi
fi
ed after installation and must always be
set less than 12 m/min, in accordance with the current
regulations.
Avoid the use of high-speed operators on the wide gate-
leaves, as this could cause strong impact against the
stops of the gate.
TECHNICAL
DATA
FORTY 5500
Single-phase system voltage
230 V AC
Frequency
50 Hz
Absorbed power
250 W
Absorbed current
1.1 A
Max Thrust force
5600 N
Max Traction force
4800 N
Max Rod speed
12 mm/s
Rod stroke
1
4m
:
275 mm
7m
: 395 mm
Max Cycles per day
2
4m
:
700
7m
: 600
Operating temperature range
3
-20°C +70°C
Operator weight (with oil)
4m
:
11 Kg
7m
:
12 Kg
Oil quantity
4
4m
:
1.9 l
7m
:
2.8 l
Oil type
5
Aprimatic
Protection class
IP55
1
for the best functioning the EFFECTIVE STROKE is reduced by 5mm.
i
IMPORTANT
:
NEVER use the limits inside the operator as a
mechanical stop.
2
Cycles reported for Environmental Temp.25°C
3
With temperatures below -15°C is recommended to set an
appropriate A
DDITIONAL
TIME
AT
END
OF
MOVEMENT
, in order to ensure
the completion of the opening / closing (set the control unit).
4
In the event of replacing the oil in the tank, reduce the indicated
quantity of 0.3 l for vers. 4M and 0.5 l for vers. 7M
5
Do not
fi
ll with oil other than that prescribed.
FORTY
5500
DS
A
4M
4M
: for wings with a MAX
width of 4m.
7M
: for wings with a width of
more than 4m up to 7m
MAX.
7M
B
4M
7M
C
4M
7M
SF
4M
7M
DS
With
hydraulic slowing-down
, for a distance of
13
mm
, approaching to the
opening
and
closing
limits
A
With
hydraulic lock for opening only
B
With
double hydraulic lock
(for opening and closing)
C
With
hydraulic lock for closing only
SF
No hydraulic lock / Frictioned
- the gate can be moved by hand, if moved slowly,
with a minimum of resistance.
- The electric lock is necessary.
IMPORTANT:
- use of an electric locking device is compulsory on wings with
a width of more than 2.0 m.
Available product versions
tab. 2 -
Technical data
tab. 1 -
