APRILIA M191M Workshop Manual Download Page 69

Page: 69 / 177

ENGINE

3 - 45

Engines M192M / M191M / M245M / M234M / M282M / M281M

3.2.4.

CHECKING THE STATOR

•

Check for continuity between connections 5-3 and 5-1
using a tester.

•

Check ground insulation of the three-stator phases 5-
ground, 3-ground and 1-ground.

Indicative resistance for each phase: 0.7 ÷ 0.9

Ω

Checking min. oil pressure switch

•

Check for continuity between connection 4 and ground
(engine off) using a tester.

Checking the Pick-Up

•

Check for a resistance of about 105 ÷ 124

Ω

at 20° C

between connection 2 and ground.

•

If different values are measured, replace defective
parts.

NOTE

The above values apply for tests carried out at room

temperature. If a stator is checked when at operating tem-
perature, higher values will be taken.

Summary of Contents for M191M


















































































































































































Search results

Summary of Contents for M191M

Reviews:

Related manuals for M191M

Brands by name

Popular brands

APRILIA M191M, Workshop Manual

Search results

Summary of Contents for M191M

Reviews:

Related manuals for M191M

Brands by name

Popular brands