APRILIA M191M Workshop Manual Download Page 122

Page: 122 / 177

ENGINE

3 - 98

Engines M192M / M191M / M245M / M234M / M282M / M281M

3.6.16. PISTON

•

Thoroughly clean piston ring locations.

•

Use suitable probes to measure the clearance between
piston rings and grooves.

•

If the clearance exceeds the permitted values change
the piston.

NOTE

For the 200 cc engine, measure the clearance by in-

serting the feeler gauge from the 2

piston ring side.

Standard coupling clearance

Max. allowed clearance after use

piston ring

0.025

0.07 mm

0.08 mm

piston ring

0.015

0.06 mm

0.07 mm

Engines M192M /
M245M / M281M /

M191M (125 - 150

cc)

Scraper ring

0.015

0.06 mm

0.07 mm

piston ring

0.015

0.06 mm

0.07 mm

piston ring

0.015

0.06 mm

0.07 mm

Engines M234M /

M282M (200 cc)

Scraper ring

0.015

0.06 mm

0.07 mm

Summary of Contents for M191M


















































































































































































Search results

Summary of Contents for M191M

Reviews:

APRILIA M191M, Workshop Manual, Page: 122 / 177

Search results

Summary of Contents for M191M

Reviews: