APRILIA M191M Workshop Manual Download Page 120

Page: 120 / 177

ENGINE

3 - 96

Engines M192M / M191M / M245M / M234M / M282M / M281M

3.6.15. GUDGEON

PIN DIAMETER

•

Check gudgeon pin outside diameter (A).

Diameter (A) (Engines M192M / M245M / M281M / M234M /
M282M) (125 - 200 cc): Ø 14,996 ÷ 15,000 mm
Diameter (A) (Engine M191M) (150 cc): Ø 14,994 ÷ 15,000
mm

•

Check gudgeon pin small end clearance.

Standard clearance: 0.015 ÷ 0.029 mm

•

Measure thrust surface diameter on piston.

Standard diameter: Ø 15.001 ÷ 15.006 mm

•

Calculate gudgeon pin-piston clearance.

Standard clearance: 0.001 ÷ 0.010 mm

NOTE

Gudgeon pin seats have lubrication ducts. Take di-

ameter reading along piston axis.

•

Measure piston outer diameter (B1 and B2) at right an-
gles to the gudgeon pin axis.

•

Take reading in the position shown in the figure:

C1=: (Engines M245M / M281M) (125 cc): 41,1 mm (from

piston crown)

C1=: (Engine M192M / M191M) (125 - 150 cc): 36,5 mm

(from piston crown)

C2=: (Engines M234M / M282M) (200 cc): 5 mm (from piston

base)

B1=

diameter (Engines M192M / M245M / M281M) (125 cc):

Ø 56.945 ÷ 56.973 mm
B1=

diameter (Engine M191M) (150 cc): Ø 56.933 ÷ 56.961

mm
B2=

diameter (Engines M234M / M282M) (200 cc): Ø 68.933

÷ 68.961 mm

Summary of Contents for M191M


















































































































































































Search results

Summary of Contents for M191M

Reviews:

APRILIA M191M, Workshop Manual, Page: 120 / 177

Search results

Summary of Contents for M191M

Reviews: