manualshive.com logo in svg

APRILIA M191M, Workshop Manual

Share
Download
APRILIA M191M Workshop Manual Download Page 72

 

 

ENGINE 

3 - 48 

Engines M192M / M191M / M245M / M234M / M282M / M281M

3.2.7. 

INSTALLING THE FLYWHEEL 

• 

Install the flywheel; ensure that the key is properly po-
sitioned. 

• 

Tighten the flywheel nut to the specified torque; lock 
the flywheel with the special tool: 

Driving pulley lock wrench (Engines M191M / M234M / 

M282M (150 - 200 cc) (adjustable face wrench) (A): 
8106702 

Driving pulley lock wrench (Engines M192M / M245M / 

M281M) (125 cc): 8140535. 

 

TIGHTENING TORQUE SETTINGS 

Engines M192M / M245M / M281M / M191M (125 - 150 cc) 
= flywheel nut: 52 ÷ 58Nm (5.2 ÷ 5.8 kgm) 
Engines M234M / M282M (200 cc) = flywheel nut: 54 ÷ 
60Nm (5.4 ÷ 6.0 kgm) 

 

 

• 

Check that Pick-Up air gap is between 0.34 and 0.76 
mm. The air gap is not adjusted when the Pick-Up is 
installed. A warped Pick-Up support will change the air 
gap value. 

NOTE 

A variation in the air gap will alter the ignition slow-

running speed. 

 

 

 

Summary of Contents for M191M


















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands