APRILIA M191M Workshop Manual Download Page 102

Page: 102 / 177

ENGINE

3 - 78

Engines M192M / M191M / M245M / M234M / M282M / M281M

3.5.6.

CLOSING THE CRANKCASE

•

Fit inner guard (1), tighten the two screws (2) to the
specified torque.

TIGHTENING TORQUE VALUES

Screws (2): 4 ÷ 6 Nm

•

Fit the oil filter union and tighten to the specified torque
value.

TIGHTENING TORQUE VALUES

Oil filter connector (3): 28 ÷ 30 Nm

•

Position gasket (4) with centering dowels (5) preferably
on the transmission-side casing.

•

Lubricate main bearings (6), install crankshaft (7) in
transmission-side casing (8).

•

Mate the two casings (8 and 9).

NOTE

When assembling the casings and the crankshaft,

take care not to damage main bearings with crankshaft-
threaded ends. For version 200 cc: set the shims in their
original position.

Summary of Contents for M191M


















































































































































































Search results

Summary of Contents for M191M

Reviews:

Related manuals for M191M

Brands by name

Popular brands

APRILIA M191M, Workshop Manual

Search results

Summary of Contents for M191M

Reviews:

Related manuals for M191M

Brands by name

Popular brands