APRILIA M191M Workshop Manual Download Page 34

Page: 34 / 177

ENGINE

3 - 10

Engines M192M / M191M / M245M / M234M / M282M / M281M

3.1.7. REMOVING

THE DRIVING PULLEY

Engines M192M / M245M / M281M / M191M (125 - 150 cc)

•

Remove the nut and the cup washer, the drive com-
mon to all kick-starter versions and the steel washer.

Driving pulley lock wrench: 8140535

•

Remove the fixed driving half pulley and the second
steel washer.

Engines M234M / M282M (200 cc)

•

Fit the special tool into the inner slots and then remove
the nut with the cup washer.

Pulley lock wrench: 8106702

•

Remove the starting sprocket and the torque limiter.

•

Remove the fixed driving half pulley and the steel wa-
sher in contact with the bushing.

•

Remove the belt and pull out the movable half pulley
with bushing. Make sure the rollers do not escape.

•

Remove roller counter plate and its shoes.

Summary of Contents for M191M


















































































































































































Search results

Summary of Contents for M191M

Reviews:

Related manuals for M191M

Brands by name

Popular brands

APRILIA M191M, Workshop Manual

Search results

Summary of Contents for M191M

Reviews:

Related manuals for M191M

Brands by name

Popular brands