manualshive.com logo in svg

APRILIA M191M, Workshop Manual

Share
Download
APRILIA M191M Workshop Manual Download Page 73

 

 

ENGINE

3 - 49

Engines M245M / M234M / M282M / M281M

3.2.8. 

FITTING THE COMPLETE FLYWHEEL COVER 

(ENGINES M245M / M281M / M234M /M282M) 
(125 - 200 CC) 

• 

Position the flywheel with its TDC mark aligned with 
the mark on the crankcase. 

 

 

 

• 

Prepare the flywheel cover: align marks between drive 
and case cover. 

• 

Fit the outside SAS cleaner and mount the cover. 

• 

Fit the inside SAS cleaner. 

 

 

WARNING 
Make sure the two centering dowels are pre-
sent. 

 

 

 

• 

Fit the cover on the engine; fit the three rods into the 
holes for the water pump drive. 

 

 

WARNING 
Ensure that the flywheel connector is properly 
fitted.  

 

 

 

• 

Tighten the cover screws. 

• 

Connect the diaphragm to the SAS delivery pipe and 
close the clamp. 

• 

Position the air duct. 

• 

Tighten the diaphragm and duct screws. 

• 

Connect the cooling sleeve and close the clamp. 

 

 

Summary of Contents for M191M


















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands