APRILIA M191M Workshop Manual Download Page 130

Page: 130 / 177

ENGINE

3 - 106

Engines M192M / M191M / M245M / M234M / M282M / M281M

3.6.24.

CHECKING VALVE SEATS FOR WEAR

•

Measure "

" mark depth on valve seat. Max. wear limit

1.6 mm.

•

Clean valve guide from any carbon deposits.

•

Measure the inner diameter of all valve guides (D).

•

Make the measurements at three different heights in
the rocker arm thrust direction.

Exhaust valve guide

D = Standard diameter: 5.000 ÷ 5.012 mm
D = Allowed limit: 5.022

Intake valve guide

D = Standard diameter: 5.000 ÷ 5.012 mm
D = Allowed limit: 5.022

•

If the valve seat mark depth values or the valve guide
diameter are above the specified limits, change the
head.

Checking valves

•

Check valve stem diameter (d – D) in the three points
shown in the figure.

Standard diameter

D1, D2 and D3=Intake: 4.972 ÷ 4.987 mm
d1, d2 and d3=Exhaust: 4.96 ÷ 4.975 mm

Min. allowed diameter

D1, D2 and D3=Intake: 4.96 mm
d1, d2 and d3=Exhaust: 4.95 mm

•

Calculate clearance between valve and valve guide.

Summary of Contents for M191M


















































































































































































Search results

Summary of Contents for M191M

Reviews:

Brands by name

Popular brands

APRILIA M191M, Workshop Manual

Search results

Summary of Contents for M191M

Reviews:

Brands by name

Popular brands