Anton Paar DMA 4100 M Instruction Manual Download Page 123

Page: 123 / 152

Appendix C: Measuring under Special Conditions

C76IB003EN-E

123

2. Hold the new foil in one hand and use the thumb finger nail of the other hand

to peel off the back liner from a small area.

3. Position the back liner free end of the foil on one edge of the display, hold the

opposite end and bend the foil backwards.

4. Peel off the back liner with one hand, simultaneously rolling the foil slowly

onto the display with the other hand.

5. Carefully flatten out the foil with a clean cotton cloth, pushing bubbles

towards the edges.

6. In case of bubbles between foil and display, gently push them towards the

edges or lift up the foil partly or completely and reapply the foil more slowly.

Summary of Contents for DMA 4100 M

























































































































































Search results

Summary of Contents for DMA 4100 M

Reviews:

Related manuals for DMA 4100 M

Brands by name

Popular brands

Anton Paar DMA 4100 M, Instruction Manual

Search results

Summary of Contents for DMA 4100 M

Reviews:

Related manuals for DMA 4100 M

Brands by name

Popular brands