American Dryer Corp. PHASE 7 OPL User Manual Download Page 8 | Manualshive

Page: 8 / 63

background image

5

O.

Cycle Preview

- entire dryer parameters (programs) or the preprogrammed cycles are displayed

for verification upon a coded entry to the keypad (touchpad).

P.

Reversing Option

- helps reduce the balling up or tangling of large items.

A cycle can be set to have the reversing option where the basket (tumbler) will turn in the forward
direction From 30 to 120 seconds, stop from 7 to 10 seconds, and then proceed in the reverse direction
for the same time. This process is repeated throughout the drying and cooling cycles.

Q.

RPM

- Phase 7 microprocessor controller also displays tumbler RPM by pressing the Down Arrow Key

and holding it, the tumbler RPM will be displayed. (The tumbler must be rotating for approximately 30
seconds before getting a true RPM reading)

R.

Clean Lint

- this feature monitors the value of the “Lint Count” register. The register contains the

acceptable limit of dryer cycles the machine will be allowed operate before the microprocessor
locks the user out. Once the feature prompts the user to “CLEAN LINT DRAWER” the dryer is now
in a locked state and

will not

be cleared until the Lint Drawer has been cleaned. When the Lint

Drawer is opened, the display will read “LINT DRAWER OPEN” and when the Lint Drawer is closed,
the display will read “READY”. (NOTE: the Lint Drawer must be opened for 15 seconds or more for
the reset to occur.) The dryer circuit is now active and can be programmed.

S.

Language Selection

- Phase 7 has the ability to display 5 different languages, English, French, Spanish,

Italian, German.

T.

Model Selection

- The Phase 7 can be programmed to be used on 3 modes of heat. Gas single burner

(200), Gas double burner (310, 410), Steam (200, 310, 410)

U.

L.E.D. Display Modes

- The display can be changed to scroll pixel or character. Also, the scrolled

messages can be either continuous, continuous with a pause or just one time. The speed of the scroll is
also adjustable for operators preference.

V.

Factory Settings

- This feature will set all programmed parameters to thier default values.

W.

Keypad Symbols

-

=

“CLEAR/STOP” key

= “ENTER/START” key

= Scroll Up

= Scroll Down

«
...
6
7
8
9
10
...
»

Summary of Contents for PHASE 7 OPL
































































Reviews:

No comments

Related manuals for PHASE 7 OPL

Brand: Maytag Pages: 188

Brand: Conair Pages: 8

Brand: CaterChef Pages: 12

DVE50R5400 Series

Brand: Samung Pages: 120

Brand: Maytag Pages: 20

DRYPOINT AC 410

Brand: Beko Pages: 56

Brand: Beko Pages: 48

Brand: Beko Pages: 64

DRYPOINT ACC 110

Brand: Beko Pages: 54

DRYPOINT RA 1080-8800

Brand: Beko Pages: 76

DRYPOINT M intelligence

Brand: Beko Pages: 40

DRYPOINT M PLUS DM 08-19 KA-N

Brand: Beko Pages: 16

DRYPOINT M DM 40-61 C

Brand: Beko Pages: 12

Brand: Beko Pages: 60

DRYPOINT M eco control

Brand: Beko Pages: 50

Brand: Beko Pages: 68

Brand: Beko Pages: 60

DRYPOINT DM 10-34 C

Brand: Beko Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands