American Dryer Corp. PHASE 7 OPL User Manual Download Page 59 | Manualshive

Page: 59 / 63

background image

56

INPUTS:

1.

FDRC – (RED LED)

This LED will indicate the status of the Front Doors. If the doors are
Closed, then the LED is ON.

2.

FDRO – (RED LED)

This LED will indicate the status of the Front Doors. If the doors are
Open, then the LED is ON.

3.

TBOL – (RED LED)

This LED will indicate the status of the Tumbler Overload Contact. If
the Contact is closed, then the LED is ON. If it faults open, then the LED is OFF.

4.

FNOL – (RED LED)

This LED will indicate the status of the Fan Overload Contact. If
the Contact is closed, then the LED is ON. If it faults open, then the LED is OFF.

5.

RDWN – (RED LED)

This LED will indicate the status of the Rear Tilt. If the rear of the
dryer is down, then the LED is ON.

6.

FDWN – (RED LED)

This LED will indicate the status of the Front Tilt. If the front of the
dryer is down, then the LED is ON.

7.

RDRC – (RED LED)

This LED will indicate the status of the Rear Doors. If the doors are
Closed, then the LED is ON.

8.

RDRO – (RED LED)

This LED will indicate the status of the Rear Doors. If the doors are
Open, then the LED is ON.

9.

FAN – (RED LED)

This LED will indicate the status of the Blower Fan. If the fan is on,
Then the LED is ON.

10. RBHL – (RED LED)

This LED will indicate the status of the Rear Burner High Limit Disk.
If the disk is closed (Temp below 330 F), Then the LED is ON.

11. R_SS – (RED LED)

This LED will indicate the status of the Rear Sail Switch. If the switch
is closed, Then the LED is ON.

12. FBHL – (RED LED)

This LED will indicate the status of the Front Burner High Limit Disk.
If the disk is closed (Temperature below 330 F), Then the LED is ON.

13. F_SS – (RED LED)

This LED will indicate the status of the Front Sail Switch. If the switch
is closed, Then the LED is ON.

14. EXHL – (RED LED)

This LED will indicate the status of the Exhaust High Limit Disk.
If the disk is closed (Temperature below 225 F), Then the LED is ON.

15. DRY – (RED LED)

This LED will indicate the status of the PLC. If the mechanical
Functions of the dryer have been set to the DRY position, the PLC will
Send a signal to the Phase 7 board. This signal will indicate that
All the Doors are closed and the dryer is level. When these conditions are met, then
the LED is ON.

16. LINT – (RED LED)

This LED will indicate the status of the Lint Drawer. If the drawer is
Closed, then the LED is ON.

«
...
57
58
59
60
61
...
»

Summary of Contents for PHASE 7 OPL
































































Reviews:

No comments

Related manuals for PHASE 7 OPL

Brand: Zanussi Pages: 19

Brand: Aurora Pages: 8

Brand: Atag Pages: 74

Brand: Maytag Pages: 51

Brand: inventum Pages: 24

ARTIST FOLD & REWIND

Brand: OBH Nordica Pages: 28

Brand: REVLON Pages: 2

Brand: Fagor Pages: 39

Brand: Amana Pages: 2

Brand: TEFAL Pages: 12

Brand: Frymaster Pages: 2

Brand: CORBERO Pages: 17

Brand: Kleenmaid Pages: 24

Brand: Indesit Pages: 16

Brand: Champion Pages: 41

Brand: Cook's Companion Pages: 20

Brand: Hitachi Pages: 200

Brand: Electrolux Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands