American Dryer Corp. PHASE 7 OPL User Manual Download Page 22 | Manualshive

Page: 22 / 63

background image

19

2.

PROGRAM “A”-“F” CYCLE - This menu allows the programming of cycle “A” - “F”. The parameters
selected in this menu for each letter will be stored in memory for that key. This will allow the operator
to utilize one touch drying through keys “A”-“F”.

3.

PROGRAM “0”-“99” CYCLE - This menu allows the programming of cycle “0”-“99”. The parameters
selected in this menu for each number will be stored in memory for that number key(s). This will allow
the operator to utilize preprogrammed drying cycles stored in memory under a numerical location.

NOTE

:

BOTH THE “A”-“F” AND “0”-“99” ALLOWS FOR A TOTAL OFF 106
PREPROGRAMMED LOCATIONS FOR CUSTOM DRYING.

4.

DEFAULT SETTINGS - This menu allows the operator to set ALL the programmable parameters to
the default settings. This option has a password selection of 1 2 3.

CAUTION:

Once the settings have been set to their default settings, there is no way to
retrieve the old settings. Use caution when using this feature.

«
...
20
21
22
23
24
...
»

Summary of Contents for PHASE 7 OPL
































































Reviews:

No comments

Related manuals for PHASE 7 OPL

Brand: Daewoo Pages: 20

Brand: Kalorik Pages: 72

Brand: Parker Pages: 100

Brand: Heinner Pages: 27

Brand: wad Pages: 27

Brand: Cylinda Pages: 91

Brand: German pool Pages: 17

Brand: Alliance Laundry Systems Pages: 34

Jet CXV TurboDryer

Brand: Dri-Eaz Pages: 11

Brand: TriStar Pages: 31

EIED55HIW - 8.0 cu. Ft. Electric Dryer

Brand: Electrolux Pages: 28

Brand: Beko Pages: 56

Brand: Beko Pages: 44

Brand: Beko Pages: 44

Brand: Beko Pages: 44

Brand: Beko Pages: 68

Brand: Beko Pages: 56

Brand: Beko Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands