American Dryer Corp. PHASE 7 OPL User Manual Download Page 28 | Manualshive

Page: 28 / 63

background image

25

4.

The dryer can be stopped at anytime by pressing the “CLEAR/STOP” key. If the temperature is
above the Cool Down setpoint when the “CLEAR/STOP” key is pressed, the dryer will go into a
Cool Down Cycle. If the “CLEAR/STOP” key is pressed again at this point the cycle that was in
progress

will be cancelled

and returned to the “READY” state. If the temperature is below the Cool

Down setpoint. The cycle that was in progress will be cancelled and go to the Wrinkle Guard.

5.

When programming a Manually Loaded cycle, if an error is made making an entry, press the “CLEAR/
STOP” key ONCE, and the entry

will be cancelled

. Re-enter the selection. If the selection is

entered and an error is made, the “CLEAR/STOP” key will cancel the program and return to the
“READY” state.

6.

Use the UP and DOWN ARROWS to scroll through menus or increase/decrease number values or
toggle between choices.

7.

In the programming mode, the number of keys can be used to jump to menu levels without scrolling
through them all. i.e., from 0 select Model in Dryer Setup, you can jump to menu level 5. Enter lint
count under Dryer Setup by pressing the 5 key followed by “ENTER/START” key to accept value.
L.E.D. display will read 5: ENTER Lint Count 1 to 5.

8.

The Tumbler temperature can be displayed by pressing and holding the UP ARROW key.

9.

The programmed cycle parameter can be viewed by pressing the “ENTER/START” key followed
by the A-F key. To view 0-99 cycles, press “ENTER/START” followed by the number desired to
view followed by “ENTER/START” . The viewing can be stopped by pressing the “CLEAR/STOP

at anytime.

«
...
26
27
28
29
30
...
»

Summary of Contents for PHASE 7 OPL
































































Reviews:

No comments

Related manuals for PHASE 7 OPL

Brand: EAS Electric Pages: 114

Brand: Teka Pages: 13

Brand: Steba Pages: 52

Brand: TurboTronic Pages: 10

Brand: Alliance Laundry Systems Pages: 19

Brand: Garland Pages: 24

Brand: LANOX Pages: 36

Brand: Frymaster Pages: 37

Brand: Waring Pages: 11

Brand: Starmix Pages: 140

AEQ6700FS - 27" Electric Dryer

Brand: Frigidaire Pages: 15

Brand: Frigidaire Pages: 11

Brand: Frigidaire Pages: 10

Brand: Frigidaire Pages: 8

Affinity FAQE7072L

Brand: Frigidaire Pages: 3

Brand: Frigidaire Pages: 10

Affinity FAQE7011L

Brand: Frigidaire Pages: 3

Brand: Frigidaire Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands