American Dryer Corp. PHASE 7 OPL User Manual Download Page 33 | Manualshive

Page: 33 / 63

background image

30

SECTION VI

PROGRAMMING INSTRUCTIONS

A. INTRODUCTION TO PROGRAMMING

The various program selections are stored in the Phase 7 OPL microprocessor controller (computer) and are broken
down into five (5) categories:

0.

Language (ENGLISH, FRANCAIS, ESPANOL, ITALIANO, DEUTSCH)

1.

System Parameters (Dryer Setup, Display Setup, Cool Down Setup, Wrinkle Guard Setup)

2.

Preprogrammed Cycles (Key “A” through Key “F”)
a.

This feature allows the operator to have six (6) most commonly used cycle selections awaiting the push
of a single keypad entry to start the dryer.

3.

Preprogrammed Cycles (“0” through “99”)
a.

This feature allows the operator to have an added one hundred (100) preprogrammed cycle selections.
These can be started by selecting the number and pressing the “ENTER/START” key.

4.

Default Settings (Returns all the programmable parameters to the default settings).

Both the preprogrammed cycles and the system parameters (programs) have been preprogrammed by the factory
with the parameters shown on

page 49

of this manual. The various program selections for the preprogrammed

cycles and system parameters are outlined in

Section III

of this manual.

ALL

program changes for the preprogrammed cycles and system parameters (programs) are done through the

keypad selection keys on the front of the control panel.

ENTERING THE PROGRAMMING MODE:
First, make sure that no cycle is in progress and that the L.E.D. display reads “READY”,

then press the “CLEAR/

STOP”

Key

and the UP ARROW key together.

This will put you into the programming mode.

EXITING THE PROGRAMMING MODE:
The “CLEAR/STOP” key will return you to the previous menu level. Continue to press the “CLEAR/STOP” key
until you are all the way out of the Programming Mode.

To alter the programming Parameters, the operator will locate the parameter (program) that is to be changed. If the
change is a numerical one (i.e., time and/or temperature), the operator will simply enter the numerical value desired.
If an error is made, press the “CLEAR/STOP” Key

ONCE

, and the incorrect entry that was made

will be

cancelled

. Once the entry is made, and the parameter (program) set does not need to be changed, press the

“ENTER/START” Key, and the Phase 7 OPL microprocessor controller (computer) will advance to the next
program selected.

If the parameter (program) change is a feature change, such as changing the temperature conversion from degree
Fahrenheit (ºF) to degree Celsius (ºC) or from “AUTO” (Automatic Drying Cycle -

Patent No. (4,827,627

) to”

MANUAL” (Timed [Manual] Drying Cycle), the operator will press the “UP ARROW” or “DOWN ARROW” Key.
This will toggle between choices. Once the entry is made, or if the parameter (program) does not need to be
changed, press the “ENTER/START” Key, and the Phase 7 OPL microprocessor controller (computer) will
advance to the next program selection.

«
...
31
32
33
34
35
...
»

Summary of Contents for PHASE 7 OPL
































































Reviews:

No comments

Related manuals for PHASE 7 OPL

Brand: Samsung Pages: 18

Brand: Samsung Pages: 40

Brand: Samsung Pages: 6

Brand: Samsung Pages: 12

Brand: Samsung Pages: 108

Brand: Maytag Pages: 40

Brand: Presto Pages: 10

Brand: Belson Pages: 7

Brand: Vulcan-Hart Pages: 28

Brand: Maytag Pages: 17

Brand: Ga.Ma Pages: 86

Brand: Blue Seal Pages: 40

Brand: Haier Pages: 12

Brand: Haier Pages: 17

Brand: Haier Pages: 22

Brand: Haier Pages: 16

Brand: Haier Pages: 24

Brand: Haier Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands