American Dryer Corp. PHASE 7 OPL User Manual Download Page 25 | Manualshive

Page: 25 / 63

background image

22

7)

Once the COOL DOWN cycle is completed the Phase 7 OPL microprocessor
controller (computer) will proceed into the Wrinkle Guard cycle. The Audio Alert tone will
sound (for amount set in Audio Alert ON time). The L.E.D. display will read “WRINKLE
GUARD”. The times are fixed at 2 minutes OFF, 2 minutes ON for a max time of 99 minutes.
These times are not programmable. During the ON time, the Blower (fan) and the basket (tumbler)
will start to rotate (without heat for 2 minutes). The Phase 7 OPL microprocessor controller
(computer) will repeat this process until the Maximum Wrinkle Guard On Time has expired (99
minutes). The L.E.D. display will then read “CYCLE DONE” and lockout the dryer functions
until the doors are opened. It will then return to “READY”.

NOTE

: Mechanical functions of the dryer is not allowed during the ON time. The Blower (fan)

must be OFF to perform mechanical functions. However the “CLEAR/STOP” key may be
pressed at any time to end the Wrinkle Guard cycle. Mechanical functions of the dryer is
allowed during the OFF time.

2. Manually Loaded Cycles

a. Automatic Drying Cycle

(Patent No. 4,827,627)

1) L.E.D. display reads “READY” (no cycle in progress).

2) Press Auto Key.

3) L.E.D. display will now read ENTER DRY TEMP 160 TO 200. (Defaults to 160

°F or 71° C)

Enter the temperature desired (from

160ºF to 200ºF in one-degree increments or from 71ºC

to 93ºC in one-degree increments). i.e., for 180 ºF, press Key “1”, Key “8”, Key “0”, and then
press the “ENTER/START” Key to accept the value.

4) L.E.D. display will now read ENTER DRY LEVEL 90 TO 100. enter the percentage of

extraction (dryness level desired) from 90% to 100% in one-percent increments (Defaults to
100%). i.e., for 95%, press Key “9”, Key “5”, and then press the “ENTER/START” Key
to accept the value.

5) L.E.D. display will now read “SELECT REVERSE MODE” (Default to ON). The ON/OFF

selection can be toggled with the UP & DOWN ARROWS. Once selected, press the “ENTER/
START” Key to accept selection.

NOTE

: In addition to entering a value by pressing the number keys, the UP and DOWN ARROWS

can be used to scroll to the number desired or toggle between selections.

6) The dryer will now display “PRESS START”. Press the “ENTER/START” Key to start

the dryer. The L.E.D. display will read AUTO DRYING CYCLE, ELAPSED TIME__MIN.
During the Drying Cycle, the Phase 7 OPL microprocessor controller (computer) is
monitoring the moisture in the load. Once the temperature is above 160 F, the Cycle

Status

portion of the L.E.D. will change from ELAPSED TIME __ MIN to __%

DRY. The

display will count upward until the percentage of extraction

programmed is reached.

NOTE

: Press and hold the “UP ARROW” to view the tumbler temperature at any time.

«
...
23
24
25
26
27
...
»

Summary of Contents for PHASE 7 OPL
































































Reviews:

No comments

Related manuals for PHASE 7 OPL

Brand: wad Pages: 27

StarlettePlus-E

Brand: Parker Pages: 148

Professional 1 Slim

Brand: Taurus Pages: 68

Brand: Indesit Pages: 16

Brand: Daewoo Pages: 20

Brand: Trisa electronics Pages: 25

Brand: Adler Europe Pages: 64

Brand: Adler Europe Pages: 64

Brand: Adler Europe Pages: 68

Brand: Tower Hobbies Pages: 24

Brand: Amana Pages: 4

Brand: Haier Pages: 12

Brand: Haier Pages: 17

Brand: Haier Pages: 22

Brand: Haier Pages: 16

Brand: Haier Pages: 24

Brand: Haier Pages: 92

Brand: Haier Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands