background image

 

 

 

 

Using the machine 

 

10.9.2 

Draining the final residues  

 

 

On the field: Spread the final residues over the field. 

 

In the courtyard:  

ο

 

Place a suitable collecting container under the drain open-
ing of the suction chest and the drain hose for the pressure 
filter and collect the final residues. 

ο

 

Dispose of the collected spray liquid residue in accordance 
with the corresponding legal guidelines. 

ο

 

Collect the spray liquid residues in suitable containers. 

 

  1.  Place a suitable collection vessel under the 

outlet opening of the VARIO switch tap on 
the suction side. 

  2.  Move switch tap 

A

 to the 

 position 

and dump the final residue from the spray 
liquid tank into a suitable collection vessel. 

  3.  Move switch tap 

A

 to the 

 position 

and dump the final residue from the suction 
chest into a suitable collection vessel. 

  4.  Place a suitable collection vessel under the 

outlet opening of the pressure filter. 

  5.  Press guard plate back; set setting tap 

C

 to 

position 

 and drain the final residue 

from the pressure filter. 

 

 

Fig. 134 

 

 

 

   

BAG0021.14  05.19

 

185 

 

Summary of Contents for UG 2200 Special





























































































































































































































































Reviews: