manualshive.com logo in svg

Altera PHY IP Core, User Manual

Share
Download
Altera PHY IP Core User Manual Download Page 91

Chapter 6: PHY IP Core for PCI Express (PIPE)

6–9

Interfaces

March 2012

Altera Corporation

Altera Transceiver PHY IP Core

User Guide

1

The 

block diagram

 shown in the GUI labels the external pins with the 

interface type

 

and places the

 interface name

 inside the box. The interface type and name are used in 

the 

_hw.tcl

 file. If you turn on 

Show signals

, the 

block diagram

 displays all top-level 

signal names.

f

For more information about 

_hw.tcl

 files, refer to refer to the 

Component Interface Tcl 

Reference

 chapter in volume 1 of the 

Quartus II Handbook

.

The following sections describe the signals in each interface. 

Avalon-ST TX Input Data from the PHYMAC 

Table 6–6

 describes the signals in the Avalon-ST input interface. These signals are 

driven from the PHYMAC to the PCS. This is an Avalon sink interface. 

f

For more information about the Avalon-ST protocol, including timing diagrams, refer 
to the 

Avalon Interface Specifications

. 

Avalon-ST RX Output Data to the PHYMAC

Table 6–7

 describes the signals in the Avalon-ST output interface. These signals are 

driven from the PHY to the PHYMAC. This is an Avalon source interface.

Table 6–6. Avalon-ST TX Inputs 

Signal Name

Dir

Description

pipe_txdata[

<n>

<

d

>-1:0]

Sink

This is TX parallel data driven from the PHYMAC for PCI Express. The 
ready latency on this interface is 0, so that the PHY must be able to 
accept data as soon as the PHY exits reset.

pipe_txdatak[

<n><d>

/8-1:0]

Sink

Data and control indicator for the received data. When 0, indicates that 

pipe_txdata

 is data, when 1, indicates that 

pipe_txdata

 is control.

Table 6–7. Avalon-ST RX Inputs 

Signal Name

Dir

Description

pipe_rxdata[

<n>

<

d

>-1:0]

Source

This is RX parallel data driven from the PHY. The ready latency on this 
interface is 0, so that the MAC must be able to accept data as soon as the 
PHY comes out of reset.

pipe_rxdatak[

<n><d>

/8-1:0]

Source

Data and control indicator for the source data. Bit 0 correspond the low 
byte of 

pipe_rxdata

. Bit 1 corresponds to the upper byte. When 0, 

indicates that 

pipe_rxdata

 is data, when 1, indicates that 

pipe_rxdata

 is control.

pipe_rxvalid[

<n>

-1:0]

Source Asserted when RX data and control are valid. 

Summary of Contents for PHY IP Core







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands