manualshive.com logo in svg

Altera PHY IP Core, User Manual

Share
Download
Altera PHY IP Core User Manual Download Page 45

Chapter 4: XAUI PHY IP Core

4–3

Performance and Resource Utilization

March 2012

Altera Corporation

Altera Transceiver PHY IP Core

User Guide

Performance and Resource Utilization

Table 4–3

 shows the typical expected device resource utilization for different 

configurations using the current version of the Quartus II software targeting a 
Stratix IV GX (EP4SG230KF40C2ES) device. 

Parameter Settings

To configure the XAUI IP core in the parameter editor, 

c

lick I

nstalled Plug-Ins

 > 

Interfaces >Ethernet> XAUI PHY v11.1

. 

This section describes the XAUI PHY IP core parameters, which you can set using the 
parameter editor. 

Table 4–4

 lists the settings available on 

General Options

 tab.

Table 4–3. XAUI PHY Performance and Resource Utilization—Stratix IV GX Device

Implementation

Number of 3.125 

Gbps Channels

Worst-Case 

Frequency

Combinational 

ALUTs

Dedicated

Registers

Memory Bits

Soft XAUI

4

183.18 MHz

4500

3200

5100

Hard XAUI

4

400 MHz

2000

1300

0

Table 4–4. General Options  (Part 1 of 2)

Name

Value

Description

Device family

A

rr

ia II GX

Cyclone IV GX

S

tr

a

t

ix IV

S

tr

a

t

ix V 

The target device family. 

S

t

a

rt

ing channel numbe

r

0–124

The physical starting channel number in the Altera device for channel 
0 of this XAUI PHY.  In Arria II GX, Cyclone IV GX, HardCopy IV and 
Stratix IV devices, this starting channel number must be 0 or a 
multiple of 4. There are no numbering restrictions for Stratix V 
devices. Assignment of the starting channel number is required for 
serial transceiver dynamic reconfiguration. 

XAUI in

t

e

r

face 

t

ype

Ha

r

d XAUI

Sof

t

 XAUI

DDR XAUI

The following 3 interface types are available:

■

Ha

r

d XAUI

–Implements the PCS and PMA in hard logic. Available 

for Arria II, Cyclone IV, HardCopy IV, and Stratix IV devices.

■

Sof

t

 XAUI

–Implements the PCS in soft logic and the PMA in hard 

logic. Available for HardCopy IV, Stratix IV, and Stratix V devices.

■

DDR XAUI

–Implements the PCS in soft logic and the PMA in hard 

logic. Both the application and serial interfaces run at twice the 
frequency of the 

Sof

t

 XAUI

 options. Available for HardCopy IV 

Stratix IV devices.

All interface types include 4 channels. 

PLL 

t

ype

CMU

ATX

You can select either the CMU or ATX PLL. The CMU PLL has a larger 
frequency range than the ATX PLL. The ATX PLL is designed to 
improve jitter performance and achieves lower channel-to-channel 
skew; however, it supports a narrower range of data rates and 
reference clock frequencies. Another advantage of the ATX PLL is 
that it does not use a transceiver channel, while the CMU PLL does. 
This parameter is available for Stratix IV soft and DDR XAUI, and 
Stratix V devices.

Summary of Contents for PHY IP Core







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands