Home
/
Altera
/
PHY IP Core
/
User Manual

Altera PHY IP Core, User Manual

Share

Page: 35 / 230

Altera PHY IP Core User Manual Download Page 35

Chapter 3: 10GBASE-R PHY IP Core

3–17

Interfaces

March 2012

Altera Corporation

Altera Transceiver PHY IP Core

User Guide

Serial Interface

Table 3–15

describes the input and outputs of the transceiver.

Register Interface

The Avalon-MM PHY management interface provides access to the 10GBASER-R
PHY PCS and PMA registers. You can use an embedded controller acting as an
Avalon-MM master to send read and write commands to this Avalon-MM slave
interface.

Table 3–16

describes the signals that comprise the Avalon-MM PHY Management

interface.

f

Refer to the “

Typical Slave Read and Write Transfers

” and “

Master Transfers

” sections in

the “

Avalon Memory-Mapped Interfaces”

chapter of the

Avalon Interface Specifications

for

timing diagrams.

Table 3–15. Transceiver Serial Interface

(1)

Signal Name

Direction

Description

rx_serial_data

<n>

Input

Differential high speed serial input data using the PCML I/O standard.
The clock is recovered from the serial data stream.

tx_serial_data

<n>

Output

Differential high speed serial input data using the PCML I/O standard.
The clock is embedded from the serial data stream.

No

t

e

t

o

Table 3–15

:

(1)

<n>

is the channel number.

Table 3–16. Avalon-MM PHY Management Interface

Signal Name

Direction

Description

phy_mgmt_clk

Input

The clock signal that controls the Avalon-MM PHY management,
interface. For Stratix IV devices, the frequency range is 37.5–50 MHz.

There is no frequency restriction for Stratix V devices; however, if you
plan to use the same clock for the PHY management interface and
transceiver reconfiguration, you must restrict the frequency range of

phy_mgmt_clk

to 100–125 MHz to meet the specification for the

transceiver reconfiguration clock.

phy_mgmt_clk_reset

Input

Global reset signal that resets the entire 10GBASE-R PHY. This signal
is active high and level sensitive.

phy_mgmt_addr[8:0]

Input

9-bit Avalon-MM address. Refer to for the address fields.

phy_mgmt_writedata[31:0]

Input

Input data.

phy_mgmt_readdata[31:0]

Output

Output data.

phy_mgmt_write

Input

Write signal. Asserted high.

phy_mgmt_read

Input

Read signal. Asserted high.

phy_mgmt_waitrequest

Output

When asserted, indicates that the Avalon-MM slave interface is unable
to respond to a read or write request. When asserted, control signals
to the Avalon-MM slave interface must remain constant.

«
...
33
34
35
36
37
...
»

Summary of Contents for PHY IP Core







































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands