manualshive.com logo in svg

Altera PHY IP Core, User Manual

Share
Download
Altera PHY IP Core User Manual Download Page 53

Chapter 4: XAUI PHY IP Core

4–11

Interfaces

March 2012

Altera Corporation

Altera Transceiver PHY IP Core

User Guide

Ports

Figure 4–3

 illustrates the top-level signals of the XAUI PHY IP core for the hard IP 

implementation. 

Figure 4–4

 illustrates the top-level signals of the XAUI PHY IP core 

for the soft IP implementation. With the exception of the optional signals available for 
debugging and the signals for dynamic reconfiguration of the transceivers, the pinout 
of the two implementations is nearly identical. The DDR XAUI soft IP signals and 
behavior are the same as the soft IP implementation.

1

The 

block diagram

 shown in the GUI labels the external pins with the 

interface type

 

and places the

 interface name

 inside the box. The interface type and name are used to 

define component interfaces in the 

_hw.tcl

. If you turn on 

Show signals

, the 

block 

diagram

 displays all top-level signal names.

f

For more information about 

_hw.tcl

 files refer to refer to the 

Component Interface Tcl 

Reference

 chapter in volume 1 of the 

Quartus II Handbook

.

Figure 4–3

 illustrates the top-level signals of the XAUI PHY IP core for the hard IP 

implementation which is available for Arria II GX, Cyclone IV GX, HardCopy IV and 
Stratix IV GX devices.

Figure 4–3. XAUI Top-Level Signals–Hard IP PCS and PMA 

xgmii_tx_dc[71:0]
xgmii_tx_clk

xgmii_rx_dc[71:0]
xgmii_rx_clk

phy_mgmt_clk
phy_mgmt_clk_reset
phy_mgmt_address[

8

:0]

phy_mgmt_writedata[31:0]
phy_mgmt_readdata[31:0]
phy_mgmt_write
phy_mgmt_read
phy_mgmt_waitrequest

pll_ref_clk
rx_analogreset
rx_digitalreset
tx_digitalreset

XAUI Top-Level Signals Hard IP Implementation

PMA

Channel

Controller

xaui_rx_serial_data[3:0]

xaui_tx_serial_data[3:0]

rx_invpolarity[3:0]

rx_set_locktodata[3:0]

rx_is_lockedtodata[3:0]

rx_set_locktoref[3:0]

rx_is_lockedtoref[3:0]

tx_invpolarity[3:0]

rx_seriallpbken[3:0]

rx_channelaligned[3:0]

rx_rmfifoempty[3:0]

rx_rmfifofull[3:0]

rx_disperr[7:0]

rx_errdetect[7:0]

rx_patterndetect[7:0]

rx_rmfifodatadeleted[7:0]

rx_rmfifodatainserted[7:0]

rx_runningdisp[7:0]

rx_syncstatus[7:0]

rx_phase_comp_fifo_error[3:0]

tx_phase_comp_fifo_error[3:0]

rx_rlv[3:0]

rx_recovered_clk[3:0]

reconfig_to_xcvr[3:0]

reconfig_from_xcvr[16:0]

cal_blk_powerdown

gxb_powerdown

pll_powerdown

pll_locked

rx_ready

tx_ready

Transceiver

Serial Data

Rx and Tx

Status

All Optional

SDR Tx XGMII 

SDR Rx XGMII 

Avalon-MM PHY

Management

Interface

Clock

and

Reset

Optional

Resets

Transceiver

Reconfiguration

(Optional)

Optional

Summary of Contents for PHY IP Core







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands